Nissan Rogue. Instruction — part 1049
SE-62
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
iv. Disconnect harness connectors from the power seat switch and lumbar support switch.
3. Release pawls and clips, and remove seat cushion outer finisher
(RH) in the direction shown (
).
: Pawl
: Metal clip
:Clip
4. Release two seatback J-clip retainers from the seat frame.
5. Partially release seatback fasteners (LH/RH).
6. Release ten seat cushion J-clips holding the seat cushion trim to the seat frame.
7. Remove seat cushion trim and seat cushion pad as an assembly from the seat frame.
8. Remove hog rings and separate seat cushion trim and seat cushion pad.
NOTE:
Remove all pieces of hog rings and discard them.
ASSEMBLY
Assembly is in the reverse order of disassembly.
• Install new hog rings on the seat cushion trim in original positions.
• Use only one hog ring in each designated location.
• Make sure hog rings are correctly fastened around both the seat
cushion trim and seat cushion pad wires.
• Use NISSAN standard hog rings and tools to assemble.
• Make sure hook fastener is pressed into place after seat cushion
trim is assembled.
• Smooth out all wrinkles during assembly.
CAUTION:
• Always route side air bag module harness in original location. Replace any deformed or damaged
clips with same type and color. Always install clips in the original location in the harness.
• After work is completed, check that no system malfunction is detected causing the air bag warning
lamp to illuminate.
• If a malfunction is detected by the air bag warning lamp after repair or replacement of the malfunc-
tion parts, perform the SRS final check. Refer to
SRC-16, "Trouble Diagnosis with CONSULT"
Lumbar Support
INFOID:0000000011280469
DISASSEMBLY
WARNING:
Do not leave any objects (screwdrivers, tools, etc.) on the seat during seatback repair. It can lead to
personal injury if the side air bag module should accidentally deploy.
CAUTION:
• Before servicing, turn the ignition switch OFF, disconnect both battery terminals, then wait at least
three minutes.
• Handle the side air bag module carefully. During disassembly, always hold the side air bag module,
do not let it hang by the wire harness.
• Always work from the side or back of the seatback, do not work in front of seat.
• Do not use air tools or electric tools for servicing the seat.
• Replace the side air bag module if it has been dropped or sustained an impact.
• Do not insert any objects into the side air bag module.
ALJIA1442ZZ
PIIB3356J
FRONT SEAT
SE-63
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
• Do not attempt to disassemble the side air bag module.
• Do not expose the side air bag module to temperatures exceeding 93
°C (199°F).
• Do not expose the side air bag module to any oil, grease, detergent or water.
• During disassembly, do not damage the seatback board, chutes, connectors, retainers, clips, module
harness or the side air bag module.
NOTE:
If the vehicle has been involved in a collision and the side air bag module has deployed, the seatback pad and
seatback trim must be replaced.
1. Remove the seatback. Refer to
2. Release hooks (A) from seatback frame and remove lumbar
support.
ASSEMBLY
Assembly is in the reverse order of disassembly.
CAUTION:
• Do not reuse the side air bag module nuts.
• Inspect seatback pad, seatback trim and seatback trim chutes. Replace if damaged.
• Smooth out all wrinkles during assembly.
• Always route side air bag module harness in original location. Replace any deformed or damaged
clips with same type and color. Always install clips in the original location in the harness.
• After work is completed, check that no system malfunction is detected causing the air bag warning
lamp to illuminate.
• If a malfunction is detected by the air bag warning lamp after repair or replacement of the malfunc-
tion parts, perform the SRS final check. Refer to
SRC-16, "Trouble Diagnosis with CONSULT"
• When installing the side air bag module, make sure there are no wrinkles and the chute is not folded,
twisted or pinched.
Front Seat Heater
INFOID:0000000011375920
SEATBACK HEATER
Removal
1. Remove seatback pad. Refer to
2. Carefully remove front seatback heater from seatback pad.
CAUTION:
• Carefully remove seatback heater from seatback pad.
• Do not damage seatback pad when removing seatback heater, if damaged replace seatback pad.
Installation
1. Peel protective backing from front seatback heater and attach to seatback pad.
2. Secure the front seatback heater harness to the seatback frame.
3. Install the remaining seatback components. Refer to
SEAT CUSHION HEATER
Removal
1. Remove seat cushion pad. Refer to
2. Carefully remove front seat cushion heater from seat cushion pad.
CAUTION:
• Carefully remove seat cushion heater from seat cushion pad.
ALJIA1478ZZ
SE-64
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
• Do not damage seat cushion pad when removing seat cushion heater, if damaged replace seat
cushion pad.
Installation
1. Peel protective backing from front seat cushion heater and attach to seat cushion pad.
2. Secure the front seat cushion heater harness to the seat cushion frame.
3. Install the remaining seat cushion components. Refer to
.
SECOND ROW SEAT
SE-65
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
SECOND ROW SEAT
Exploded View
INFOID:0000000011280470
RH SEAT
AWJIA1618ZZ
1.
Headrest
2.
Seatback upper luggage board
3.
Seatback luggage board
4.
Seatback trim
5.
Seatback pad
6.
Seatback pad wire
7.
Recline release cable
8.
Seat cushion trim
9.
Fold flat strap
10. Seat cushion pad
11. Seat cushion silencer
12. Seat cushion pad wire
13. Bolt cover
14. Seat cushion outer finisher (RH) 15. Seat cushion inner finisher (RH)
16. Seat cushion frame
17. Seat cushion frame
18. Seat cushion slide (RH)
19. Seat cushion slide cable
20. Rear bolt cover (RH) (with third
row seat)
21. Front bolt cover (RH)
22. Front bolt cover (LH)
23. Rear bolt cover (LH) (with third
row seat)
24. Seat cushion slide (LH)
25. Seat cushion inner finisher (LH) 26. Seat cushion outer finisher (LH) 27. Seat cushion rear finisher (LH)
28. Seat belt buckle
29. Recline lever finisher
30. Seatback frame
31. Recline device
32. Recline device cover
33. Headrest holder (locked)
34. Headrest holder (free)
Clip
Pawl
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст