Nissan Rogue. Instruction — part 224
DAS
PRE-INSPECTION FOR DIAGNOSIS
DAS-67
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
PRE-INSPECTION FOR DIAGNOSIS
Inspection Procedure
INFOID:0000000011277202
1.
CHECK REAR VIEW CAMERA LENS
Is the rear view camera lens contaminated with foreign materials?
YES
>> Clean rear view camera lens.
NO
>> GO TO 2.
2.
CHECK REAR VIEW CAMERA INSTALLATION CONDITION
Check rear view camera installation condition (e.g. position, looseness, bent in back door).
Is it properly installed?
YES
>> Inspection End.
NO
>> Install rear view camera properly, and perform rear view camera calibration. Refer to
DAS-68
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
REAR VIEW CAMERA WASHER/AIR BLOWER FUNCTION INSPECTION
REAR VIEW CAMERA WASHER/AIR BLOWER FUNCTION INSPECTION
Inspection Procedure
INFOID:0000000011277203
1.
CHECK REAR VIEW CAMERA WASHER/AIR BLOWER FUNCTION
1. Start the engine.
2. Select the “Active Test” item “AIR&WASH ACTIVE” of “AVM” using CONSULT.
NOTE:
Before function check, perform the following items:
• Fill with washer fluid.
• Perform “Active Test” item “WASH ACTIVE” of “AVM” using CONSULT for 4 seconds.
3. While operating the test item, check the operation.
Is it properly operated?
Washer fluid ejects 4 - 6 times. (Normal function)>>Inspection End.
Washer fluid ejects 7 times or more.>>Properly install or replace air tube.
Washer fluid ejects only once>> Properly install or replace air tube.
Washer fluid does not eject>>Properly install washer tube or replace washer tube and check valve.
DAS
ADDITIONAL SERVICE WHEN REPLACING DISTANCE SENSOR
DAS-69
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
ADDITIONAL SERVICE WHEN REPLACING DISTANCE SENSOR
Description
INFOID:0000000011277204
Always perform the following after removing and installing or replacing the Distance sensor:
• Distance sensor initial vertical alignment
• Distance sensor alignment
•
CAUTION:
The system does not operate normally unless the Distance sensor is aligned properly.
Work Procedure
INFOID:0000000011277205
1.
DISTANCE SENSOR INITIAL VERTICAL ALIGNMENT
Perform the distance sensor initial vertical alignment. Refer to
.
>> GO TO 2.
2.
DISTANCE SENSOR ALIGNMENT
Perform the distance sensor alignment. Refer to
.
>> Work End.
DAS-70
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
DISTANCE SENSOR INITIAL VERTICAL ALIGNMENT
DISTANCE SENSOR INITIAL VERTICAL ALIGNMENT
Description
INFOID:0000000011277206
WARNING:
Radio waves could adversely affect electric medical equipment. Those who use a pacemaker should
contact the electric medical equipment manufacturer for the possible influences before use.
OUTLINE OF DISTANCE SENSOR INITIAL ALIGNMENT PROCEDURE
• Always perform the Distance sensor initial vertical alignment after removing and installing or replacing the
Distance sensor.
CAUTION:
The system does not operate normally unless the Distance sensor is aligned properly.
1. Required tools, refer to
2. Preparation, refer to
3. Distance sensor initial vertical alignment, refer to
DAS-71, "Distance Sensor Initial Vertical Alignment"
CAUTIONARY POINT FOR DISTANCE SENSOR ALIGNMENT PROCEDURE
CAUTION:
• For Distance sensor alignment procedure, choose a level location with a few feet of working space in
front and surrounding the vehicle.
• Vehicle must be stationary and unoccupied during the whole alignment procedure.
• Never enter the vehicle during distance sensor alignment.
• For proper system operation and adjustment, all vehicle wheels must be the original factory size.
The Distance sensor requires alignment whenever the Distance sensor is removed and reinstalled and when-
ever front end structural repairs are performed. Distance sensor alignment consists of performing the mechan-
ical vertical alignment (Distance sensor initial vertical alignment) described in the following procedure,
followed by the electronic horizontal alignment (Distance sensor alignment) that is performed using CONSULT
and the appropriate special service tools.
Required Tools
INFOID:0000000011277207
The following tool is necessary to perform the Distance sensor initial vertical alignment:
• Carpenters level.
Preparation
INFOID:0000000011277208
1.
PREPARATION FOR DISTANCE SENSOR INITIAL VERTICAL ALIGNMENT PROCEDURE
1. Verify correct vehicle suspension height. Refer to
.
2. Repair or replace any damaged body components.
3. Verify proper tire inflation pressures. Refer to
.
4. Remove any accumulations of mud, snow or ice from the vehicle underbody.
5. Verify that there is no load in the vehicle (cargo or passenger).
6. Place the vehicle on a known level horizontal surface such as a wheel or frame alignment rack to achieve
satisfactory sensor vertical alignment results.
7. Remove front fascia. Refer to
EXT-17, "Removal and Installation"
AWOIA0048ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст