Nissan Rogue. Instruction — part 225
DAS
DISTANCE SENSOR INITIAL VERTICAL ALIGNMENT
DAS-71
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
>> Refer to
DAS-71, "Distance Sensor Initial Vertical Alignment"
.
Distance Sensor Initial Vertical Alignment
INFOID:0000000011277209
NOTE:
The Distance sensor initial vertical alignment procedure must be performed anytime the Distance sensor is
removed and reinstalled.
1. The Distance sensor (1) is located near the right front head lamp
behind the front bumper fascia.
2. Place the carpenters level (2) against the face of the Distance
sensor (1).
3. Turn the Distance sensor adjustment screw (3) to level the sen-
sor.
4. Ensure the Distance sensor electrical connector located on the bottom of the sensor is connected.
5. Reinstall the front bumper fascia.
6. Perform the Distance sensor alignment procedure. Refer to
.
AWOIA0049ZZ
AWOIA0050ZZ
AWOIA0051ZZ
DAS-72
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
DISTANCE SENSOR ALIGNMENT
DISTANCE SENSOR ALIGNMENT
Description
INFOID:0000000011277210
WARNING:
Radio waves could adversely affect electric medical equipment. Those who use a pacemaker should
contact the electric medical equipment manufacturer for the possible influences before use.
OUTLINE OF RADAR ALIGNMENT PROCEDURE
• A 4-wheel vehicle alignment must be performed before proceeding with radar alignment procedure.
• Always perform the radar alignment after removing and installing or replacing the Distance sensor.
• If the Distance sensor was removed and installed or replaced, first perform Distance Sensor Initial Vertical
Alignment, refer to
.
CAUTION:
The system does not operate normally unless the Distance sensor is aligned properly.
1. Required tools, refer to
2. Preparation, refer to
3. Vehicle set up, refer to
.
4. Setting the Distance sensor target board, refer to
DAS-76, "Setting The Distance Sensor Target Board"
.
5. Distance sensor adjustment, refer to
DAS-77, "Distance Sensor Adjustment"
.
CAUTIONARY POINT FOR RADAR ALIGNMENT PROCEDURE
CAUTION:
• For radar alignment procedure, choose a level location with a few feet of working space in front and
surrounding the vehicle.
• Vehicle must be stationary and unoccupied during the whole alignment procedure.
• Any slight vibration during the alignment procedure can cause the test to fail. If this happens, you
will have to restart the alignment process.
• The ignition switch must be in the ON position.
• The battery voltage must not fall below 12 volts during the whole alignment procedure. Failure to
maintain adequate battery voltage will cause the test to fail. If this happens, you will have to restart
the alignment process.
• The Distance sensor target board must be set in front of the vehicle facing the sensor.
• Adjust the radar alignment with CONSULT. (The radar alignment procedure cannot be adjusted with-
out CONSULT.)
• Never enter the vehicle during radar alignment.
• Never block the area between the radar and the Distance sensor target board at any time during the
alignment process.
• Never break the laser beam between the laser assembly and front Distance sensor target board or
rear reflector at any time during alignment.
• Accurate steering wheel setting is crucial. Once set, do not disturb the steering wheel for the
remainder of the alignment procedure.
• To avoid physical damage, the Distance sensor adjustment screw must not be forced to either clock-
wise or counter-clockwise limit. For proper adjustment procedure, follow the directions of the CON-
SULT exactly as instructed.
• For proper system operation and adjustment, all vehicle wheels must be of the same size.
Required Tools
INFOID:0000000011277211
• Distance sensor alignment kit 1-20-2851-1 in addition to one of the following:
a) Hunter self-centering wheel adapter (Hunter wheel alignment tool)
b) Special Service Tool kit 1-20-2722-1 (kit SCA W/Tire Clamp-ICC Aiming)
The following Distance sensor alignment kit (1-20-2851-1) is necessary to perform the Distance sensor align-
ment:
DAS
DISTANCE SENSOR ALIGNMENT
DAS-73
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
• Distance sensor target board (1).
• Hunter self-centering wheel adapter (1) [shown with laser assem-
bly (2) installed] (Hunter alignment rack head may be substituted).
NOTE:
Dealers that are not equipped with a Hunter self-centering wheel
adapter will require the following kit:
Part No. 1-20-2722-1-IF (kit SCA W/Tire Clamp-Distance Sensor
Aiming)
• Laser assembly (with bi-directional laser beam) as shown in the
illustration.
- Tightening knob (1)
- Power ON/OFF button (2)
- Front laser beam opening (3)
- Rear laser beam opening (4)
- Attaching shaft (5)
• Stationary target as shown in the illustration.
- Stationary target (1)
- Laser signal reception plate (2)
• Distance chain (not shown).
Preparation
INFOID:0000000011277212
1.
ADVANCE PREPARATION FOR RADAR ALIGNMENT PROCEDURE
1. Adjust all tire pressures to the specified value.
2. Empty the vehicle. (Remove any luggage from the passenger compartment, luggage room, etc.)
3. Shift the selector lever to “P” position, and release the parking brake.
4. Fully fill the fuel tank, and then check that the coolant and oils are filled up to correct level.
5. Clean off the right front side of the fascia in front of the Distance sensor.
AWOIA0052ZZ
ALOIA0118ZZ
ALOIA0116ZZ
ALOIA0117ZZ
DAS-74
< BASIC INSPECTION >
[DRIVER ASSISTANCE SYSTEM]
DISTANCE SENSOR ALIGNMENT
NOTE:
The Distance sensor is located behind the fascia and it is not
exposed to the elements. Therefore it should not require any
cleaning.
>> Refer to
.
Vehicle Set Up
INFOID:0000000011277213
DESCRIPTION
Accurate adjustment of the radar alignment requires that the Distance sensor target board, wheel adapter,
laser assembly, and stationary target be properly positioned.
CAUTION:
If the radar alignment is adjusted with the Distance sensor target board, wheel adapter, laser assem-
bly, or stationary target in the incorrect position, the Distance system will not function properly or the
alignment procedure may not be completed successfully.
1.
PREPOSITION TARGET BOARD
NOTE:
• The center of the distance sensor (A).
• To locate the center of the distance sensor (A) easily, on a flat level
surface measure 27 in (685 mm) (H) up from the floor, and 7 in
(178 mm) (W) to the right from the point of the right front head
lamp (1) when viewed from the front of the vehicle.
• Initial distance sensor target board setting must be in the center position.
1
: Distance sensor
AWOIA0049ZZ
B : Up-down direction adjusting screw
AWOIA0053ZZ
AWOIA0054ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст