Nissan Rogue. Instruction — part 357
DLK-270
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR LOCK
BACK DOOR LOCK
Exploded View
INFOID:0000000011279038
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000011279039
REMOVAL
1. Remove back door finisher. Refer to
INT-38, "Removal and Installation"
.
2. Disconnect the harness connector from the back door lock.
3. Remove bolts and back door lock.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Tighten bolts to specification. Refer to
• After installation, check back door open/close and lock/unlock operation.
SPINDLE UNIT
SPINDLE UNIT : Removal and Installation
INFOID:0000000011279040
REMOVAL
1. Support back door using a suitable tool.
1.
Spindle unit (RH) (with automatic
back door)
2.
Back door stay (RH)
3.
Back door touch sensor (RH) (with
automatic back door)
4.
Back door lock
5.
Back door lock (with automatic back
door)
6.
Back door touch sensor (LH) (with
automatic back door)
7.
Back door
8.
Back door stay (LH)
9.
Spindle unit (LH) (with automatic
back door)
AWKIA2931ZZ
2015 Rogue NAM
BACK DOOR LOCK
DLK-271
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
WARNING:
Bodily injury may occur if the back door is not supported properly when removing the back door
spindle unit.
2. Partially remove headlining (rear edge). Refer to
3. Remove ball socket spring (B) from spindle unit (1) using a suit-
able tool (A).
4. Disconnect the harness connector from the spindle unit and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• When reusing stud ball, always apply locking sealant before installing stud ball to back door.
• After installation, check back door open/close, lock/unlock operation.
• Perform calibration of automatic back door position information. Refer to
.
BACK DOOR STAY
BACK DOOR STAY : Removal and Installation
INFOID:0000000011279041
REMOVAL
1. Support the back door using a suitable tool.
WARNING:
Body injury may occur if no supporting rod is holding the back door open when removing the
back door stay.
2. Release the metal clip (3) located on the connection between
the back door stay (1) and the stud ball (2) (back door side)
using a suitable tool (A).
3. Remove the back door stay (back door side).
4. Repeat procedure for removing back door stay from body side.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check the back door open/close operation.
TOUCH SENSOR
TOUCH SENSOR : Removal and Installation
INFOID:0000000011279042
CAUTION:
Use care not to bend touch sensor.
ALKIA3426ZZ
JMKIA2255ZZ
2015 Rogue NAM
DLK-272
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR LOCK
REMOVAL
1. Release the spindle unit from the stud ball (with power back door).
2. Release the back door stay from the stud ball (without power back door).
3. Release touch sensor clips using a suitable tool.
4. Disconnect the harness connector from the touch sensor and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check back door open/close and lock/unlock operation.
EMERGENCY LEVER
EMERGENCY LEVER : Unlock procedures
INFOID:0000000011279043
UNLOCK PROCEDURES
NOTE:
If back door lock cannot be unlocked due to a malfunction or battery discharge, perform the following proce-
dures to unlock back door assembly.
1. From inside the vehicle, rotate emergency lever (1) in the direc-
tion shown to unlock.
AWKIA2921ZZ
2015 Rogue NAM
FUEL FILLER LID OPENER
DLK-273
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FUEL FILLER LID OPENER
Exploded View
INFOID:0000000011279044
FUEL FILLER LID
FUEL FILLER LID : Removal and Installation
INFOID:0000000011279045
REMOVAL
1. Remove fuel cap pin (1).
1.
Fuel filler lid release cable
2.
Fuel filler lid release handle
3.
Spring
4.
Bumper rubber
5.
Fuel filler lid lock
A.
Screw
AWKIA2922ZZ
ALKIA3416ZZ
2015 Rogue NAM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст