Nissan Rogue. Instruction — part 815
BODY SIDE TRIM
INT-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
3. Remove nut (A) then insert suitable tool (B) to release clip, then
remove dash side finisher.
: Clip
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clips for deformation and damage during installation. Replace with new ones if
necessary.
• When installing dash side finisher, make sure insulation does not cover stud bolt.
• When installing dash side finisher, check that the clips are securely placed in body panel holes.
AWJIA1325ZZ
INT-26
< REMOVAL AND INSTALLATION >
FLOOR TRIM
FLOOR TRIM
Exploded View
INFOID:0000000011277485
Removal and Installation
INFOID:0000000011277486
CAUTION:
Before servicing, turn the ignition switch off, disconnect both battery cables and wait at least three
minutes.
REMOVAL - Front Floor Trim
1. Disconnect the negative and positive battery terminals, then wait at least three minutes. Refer to
2. Remove front door welts (LH/RH). Refer to
INT-23, "BODY SIDE WELT : Removal and Installation - Front
.
3. Remove rear door welts (LH/RH). Refer to
INT-23, "BODY SIDE WELT : Removal and Installation - Rear
.
4. Remove driver and passenger seat (LH/RH). Refer to
SE-32, "DRIVER SIDE : Removal and Installation"
5. Remove second row seats. Refer to
SE-39, "Removal and Installation"
6. Disconnect harness connectors from seatbelt pretensioners.
7. Remove dash side finisher (LH/RH). Refer to
INT-24, "DASH SIDE FINISHER : Removal and Installation"
.
1.
Rear floor trim (with third row
seat)
2.
Rear floor trim (without third
row seat)
3.
Floor trim hook
4.
Front floor trim
5.
Front floor spacer (RH)
6.
Front floor spacer (LH)
7.
Rear floor spacer (LH)
8.
Rear floor spacer (RH)
9.
Third row floor spacer (LH)
10. Third row floor spacer (RH)
Front
ALJIA1345ZZ
FLOOR TRIM
INT-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
8. Remove shift selector. Refer to
TM-193, "Removal and Installation"
.
9. Remove center pillar upper finisher (LH/RH). Refer to
INT-21, "CENTER PILLAR UPPER FINISHER :
.
10. Remove the front floor connecting ducts (LH/RH). Refer to
VTL-10, "FRONT FLOOR DUCT : Removal
and Installation - Front Floor Connecting Duct"
.
11. Disconnect front parking brake cable from rear parking brake cable and remove bolts from parking brake
cable hold down. Refer to
12. Disconnect heating and cooling unit assembly drain hose from floor.
13. Release clips (A) using a suitable tool and remove steering joint
floor cover (1).
14. Remove floor trim hooks (1) using a suitable tool (A) and front
floor trim.
15. Remove the following parts (if necessary).
• Front floor spacer (LH/RH)
• Rear floor spacer (LH/RH)
INSTALLATION
Installation is in the reverse order of removal.
REMOVAL - Rear Floor Trim
CAUTION:
Before servicing, turn the ignition switch off, disconnect both battery cables and wait at least three
minutes.
1. Disconnect the negative and positive battery terminals, then wait at least three minutes. Refer to
2. Partially remove front door welts (LH/RH). Refer to
INT-23, "BODY SIDE WELT : Removal and Installation
3. Partially remove rear door welts (LH/RH). Refer to
INT-23, "BODY SIDE WELT : Removal and Installation
.
4. Remove second row seats. Refer to
SE-39, "Removal and Installation"
5. Remove seat belt lower anchor bolt (LH/RH).
CAUTION:
Before removing the seat belt lower anchor bolt, note the positions of washers and spacers for
correct installation.
6. Remove luggage side lower finisher (LH/RH). Refer to
INT-34, "LUGGAGE SIDE LOWER FINISHER :
Removal and Installation - With Third Row Seat"
.
ALJIA1359ZZ
JMJIA1002ZZ
INT-28
< REMOVAL AND INSTALLATION >
FLOOR TRIM
7. Remove third row seats (if equipped). Refer to
SE-43, "Removal and Installation"
8. Remove rear floor trim.
INSTALLATION
Installation is in the reverse order of removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст