Nissan Rogue. Instruction — part 1247
WT-64
< PERIODIC MAINTENANCE >
WHEEL AND TIRE
WHEEL AND TIRE
Adjustment
INFOID:0000000011280544
BALANCING WHEELS (ADHESIVE WEIGHT TYPE)
Preparation Before Adjustment
Remove inner and outer balance weights from the wheel. Using releasing agent, remove double-faced adhe-
sive tape from the wheel and tire.
CAUTION:
• Be careful not to scratch the wheel and tire during removal.
• After removing double-faced adhesive tape, wipe clean all traces of releasing agent from the wheel
and tire.
Wheel Balance Adjustment
CAUTION:
• DO NOT use center hole cone-type clamping machines to hold the wheel during tire removal/installa-
tion or balancing or damage to the wheel paint, cladding or chrome may result. Use only rim-type or
universal lug-type clamping machines to hold the wheel during servicing.
• If a balancer machine has an adhesive weight mode setting, select the adhesive weight mode setting and
skip Step 2 below. If a balancer machine only has the clip-on (rim flange) weight mode setting, follow Step 2
to calculate the correct size adhesive weight.
1. Set wheel and tire on balancer machine using the center hole as a guide. Start the balancer machine.
2. For balancer machines that only have a clip-on (rim flange) weight mode setting, follow this step to calcu-
late the correct size adhesive weight to use. When inner and outer imbalance values are shown on the
balancer machine indicator, multiply outer imbalance value by 5/3 (1.67) to determine balance weight that
should be used. Select the outer balance weight with a value closest to the calculated value above and
install in to the designated outer position of or at the designated angle in relation to the wheel and tire.
a. Indicated imbalance value
× 5/3 (1.67) = balance weight to be
installed
Calculation example:
23 g (0.81 oz)
× 5/3 (1.67) = 38.33 g (1.35 oz) ⇒ 40 g (1.41 oz)
balance weight (closer to calculated balance weight value)
NOTE:
Note that balance weight value must be closer to the calculated
balance weight value.
Example:
37.4
⇒ 35 g (1.23 oz)
37.5
⇒ 40 g (1.41 oz)
SMA054D
WHEEL AND TIRE
WT-65
< PERIODIC MAINTENANCE >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
3. Install balance weight in the position shown.
CAUTION:
• Do not install the inner balance weight before installing
the outer balance weight.
• Before installing the balance weight, be sure to clean the
mating surface of the wheel and tire.
• When installing balance weight (1) to wheel and tire, set it into
the grooved area (A) on the inner wall of the wheel and tire as
shown so that the balance weight center (B) is aligned with the
balancer machine indication position (angle) (C).
CAUTION:
• Always use Genuine NISSAN adhesive balance weights.
• Balance weights are non-reusable; always replace with
new ones.
• Do not install more than three sheets of balance
weights.
4. If calculated balance weight value exceeds 50 g (1.76 oz), install
two balance weight sheets in line with each other as shown.
CAUTION:
Do not install one balance weight sheet on top of another.
5. Start balancer machine again.
6. Install balance weight on inner side of wheel and tire in the bal-
ancer machine indication position (angle).
CAUTION:
Do not install more than two balance weights.
7. Start balancer machine. Make sure that inner and outer residual
imbalance values are 5 g (0.17 oz) each or below.
8. If either residual imbalance value exceeds 5 g (0.17 oz), repeat installation procedures.
TIRE ROTATION
• Follow the maintenance schedule for tire rotation service intervals.
MA-7, "Introduction of Periodic Maintenance"
.
• Rotate the wheels and tires front to back in the pattern as shown.
• When installing the wheel, tighten wheel nuts to the specified
torque.
WARNING:
• Do not include the spare tire (if equipped) when rotating
tires.
• After rotating tires, check and adjust the tire pressure.
CAUTION:
• When installing wheel nuts, tighten them diagonally by
dividing the work two to three times in order to prevent the
wheels from developing any distortion.
• Be careful not to tighten the wheel nuts to a torque exceeding specification to prevent strain on the
disc brake rotor.
• Use Genuine NISSAN wheel nuts.
JPEIC0040ZZ
Wheel balance
Dynamic (At flange)
Static (At flange)
Maximum allowable im-
balance
Refer to
.
PEIA0033E
SMA829C
WT-66
< PERIODIC MAINTENANCE >
WHEEL AND TIRE
• Perform the ID registration after tire rotation. Refer to
Wheel nut tightening torque
: Refer to
.
WHEEL AND TIRE
WT-67
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
REMOVAL AND INSTALLATION
WHEEL AND TIRE
Exploded View
INFOID:0000000011280545
Removal and Installation
INFOID:0000000011280546
REMOVAL
1. Remove wheel nuts using power tool.
2. Remove wheel and tire.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• When installing wheel nuts, tighten them diagonally by dividing the work two or three times in order
to prevent the wheels from developing any distortion.
• Be careful not to tighten the wheel nuts to a torque exceeding specification to prevent strain on the
disc brake rotor.
• Use Genuine NISSAN wheel nuts.
1.
Wheel and tire
2.
Wheel nut
AWEIA0313ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст