Nissan Rogue. Instruction — part 1246
WT-60
< SYMPTOM DIAGNOSIS >
EASY FILL TIRE ALERT DOES NOT ACTIVATE
EASY FILL TIRE ALERT DOES NOT ACTIVATE
Description
INFOID:0000000011280540
The Easy Fill tire alert does not function while inflating a tire when the select lever position is in P-range with
the ignition switch ON.
NOTE:
• After starting to inflate the tire, it takes a few seconds for the easy fill tire alert to function.
• If there is no response for approximately 15 seconds or more after inflating the tires, cancel the use of the
Easy Fill tire alert function or move the vehicle approximately 1 m (3.2 ft.) backward or forward to try again.
The air filler pressure may be weak or out of service area.
• For Easy Fill tire alert, Refer to
WT-11, "Easy Fill Tire Alert Function"
Diagnosis Procedure
INFOID:0000000011280541
1.
LOCATION CHANGE
Move the vehicle to other area and repeat the procedure of the Easy Fill tire alert function. Refer to
"Easy Fill Tire Alert Function"
Is the function normal?
YES
>> Inspection End.
NO
>> GO TO 2.
2.
PERFORM BCM SELF-DIAGNOSIS
With CONSULT
Perform “Self Diagnostic Result” for “AIR PRESSURE MONITOR”.
Is any DTC detected?
YES
>> Perform diagnosis for detected DTC. Refer to
.
NO
>> GO TO 3.
3.
CHECK HAZARD WARNING LAMP OPERATION
Check hazard warning lamp operation with hazard switch.
Does the hazard warning lamps operate?
YES
>> GO TO 4.
NO
>> Refer to
.
4.
PERFORM SELF DIAGNOSTIC RESULT FOR TCM
With CONSULT
Perform “Self Diagnostic Result” for “TRANSMISSION”.
Is any DTC detected?
YES
>> Perform diagnosis for detected DTC. Refer to
NO
>> GO TO 5.
5.
CHECK HORN OPERATION
Check horn operation.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace malfunctioning components.
6.
PERFORM SELF DIAGNOSTIC RESULT
With CONSULT
1. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for
10 minutes.
2. Stop the vehicle.
3. Perform “Self Diagnostic Result” for “AIR PRESSURE MONITOR”.
Is any DTC detected?
YES
>> Perform diagnosis for detected DTC. Refer to
EASY FILL TIRE ALERT DOES NOT ACTIVATE
WT-61
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
NO
>> Replace BCM. Refer to
BCS-75, "Removal and Installation"
(with Intelligent Key system) or
135, "Removal and Installation"
(without Intelligent Key system).
WT-62
< SYMPTOM DIAGNOSIS >
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000011280542
Use the chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×: Applicable
Reference page
—
—
, o
r
or
—
—
or
.
Possible cause and SUSPECTED PARTS
Imp
rop
er i
nst
al
la
tio
n,
lo
os
en
es
s
O
ut
-of-ro
un
d
Im
ba
la
nc
e
Incorrect t
ire pressure
Un
ev
en
tire
wea
r
De
form
at
ion
o
r da
ma
ge
No
n-u
nif
orm
ity
Incorrect t
ire size
PROPELLER SHAFT (if
equipped)
DIF
F
ERENTIA
L (i
f equipped)
FRONT AXLE AND
FRONT
SUSP
ENSION
REAR AXLE AND
REAR
SUSP
ENSION
TI
RE
W
H
EEL
DRIVE
SHAFT
BRAK
E
ST
EERING
Symptom
TIRE
Noise
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
×
×
×
×
×
×
Shudder
×
×
×
×
×
×
×
×
×
×
×
×
Poor quality ride or
handling
×
×
×
×
×
×
×
×
×
×
WHEEL
Noise
×
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
×
×
Shimmy, Shudder
×
×
×
×
×
×
×
×
×
Poor quality ride or
handling
×
×
×
×
×
×
×
WHEEL
WT-63
< PERIODIC MAINTENANCE >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
PERIODIC MAINTENANCE
WHEEL
Inspection
INFOID:0000000011280543
WHEEL
1. Check tires for wear and improper inflation.
2. Check wheels for deformation, cracks and other damage. If deformed, remove wheel and check wheel
runout.
3. Remove tire from wheel and mount wheel on a balancer
machine.
CAUTION:
DO NOT use center hole cone-type clamping machines to
hold the wheel during tire removal/installation or balancing
or damage to the wheel paint, cladding or chrome may
result. Use only rim-type or universal lug-type clamping
machines to hold the wheel during servicing.
a. Set dial indicator as shown.
b. Check runout, if runout value exceeds the limit, replace wheel.
Limit
Axial Runout (A)
.
Radial Runout (B)
.
SEIA0737E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст