Nissan Rogue. Instruction — part 1098
B2192 ID DISCORD, IMMU-ECM
SEC-171
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2192 ID DISCORD, IMMU-ECM
DTC Logic
INFOID:0000000011278581
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check DTC in “Self Diagnostic Result” of “BCM” using CONSULT.
Is DTC detected?
YES
>> GO TO
SEC-171, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011278582
1.
PERFORM INITIALIZATION
Perform initialization of BCM and reregistration of all keys using CONSULT. Refer to the CONSULT Immobi-
lizer mode and follow the on-screen instructions.
Can the system be initialized and can the engine be started with reregistered key?
YES
>> Inspection End.
NO
>> GO TO 2.
2.
CHECK SELF-DIAGNOSTIC RESULT
1. Select “Self Diagnostic Result” of “BCM” using CONSULT.
2. Erase DTC.
3. Perform DTC CONFIRMATION PROCEDURE for DTC B2192. Refer to
.
Is DTC detected?
YES
>> GO TO 3.
NO
>> Inspection End.
3.
REPLACE BCM
1. Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
2. Perform initialization of BCM and reregistration of all keys using CONSULT. Refer to the CONSULT Immo-
bilizer mode and follow the on-screen instructions.
Can the system be initialized and can the engine be started with registered key?
YES
>> Inspection End.
NO
>> GO TO 4.
4.
REPLACE ECM
1. Replace ECM. Refer to
EC-502, "Removal and Installation"
2. Perform “ADDITIONAL SERVICE WHEN REPLACING ECM”. Refer to
>> Inspection End.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2192
ID DISCORD BCM-ECM
The ID verification results between
BCM and ECM are NG.
• Harness or connectors
(The CAN communication line is open
or shorted.)
• BCM
• ECM
2015 Rogue NAM
SEC-172
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
B2193 CHAIN OF ECM-IMMU
B2193 CHAIN OF ECM-IMMU
DTC Logic
INFOID:0000000011278583
DTC DETECTION LOGIC
NOTE:
• If DTC B2193 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B2193 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check DTC in “Self Diagnostic Result” of “BCM” using CONSULT.
Is DTC detected?
YES
SEC-172, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011278584
NOTE:
• If DTC B2193 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B2193 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
1.
CHECK BCM POWER SUPPLY AND GROUND CIRCUIT.
Check BCM power supply and ground circuit. Refer to
BCS-128, "Diagnosis Procedure"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the harness.
2.
CHECK ECM POWER SUPPLY AND GROUND CIRCUIT.
Check ECM power supply and ground circuit. Refer to
Is the inspection result normal?
YES
>> Replace ECM. Refer to
EC-502, "Removal and Installation"
. GO TO 3.
NO
>> Repair or replace the harness.
3.
PERFORM DTC CONFIRMATION PROCEDURE.
Perform the DTC confirmation procedure. Refer to
Does the DTC return?
YES
>> Replace BCM. Refer to
BCS-135, "Removal and Installation"
NO
>> Inspection End.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2193
CHAIN OF BCM-ECM
Inactive communication between BCM
and ECM.
• Harness or connectors
(The CAN communication line is open or
shorted.)
• ECM
• BCM
2015 Rogue NAM
B2196 DONGLE UNIT
SEC-173
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2196 DONGLE UNIT
Description
INFOID:0000000011278585
BCM performs ID verification between BCM and dongle unit.
When verification result is OK, BCM permits cranking.
DTC Logic
INFOID:0000000011278586
DTC DETECTION LOGIC
NOTE:
• If DTC B2196 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B2196 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Turn ignition switch OFF.
3. Turn ignition switch ON.
4. Check “Self Diagnostic Result” of “BCM” using CONSULT.
Is the DTC detected?
YES
>> Refer to
SEC-173, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011278587
Regarding Wiring Diagram information, refer to
1.
PERFORM INITIALIZATION
1. Perform initialization of BCM and reregistration of all keys using CONSULT. Refer to the CONSULT Immo-
bilizer mode and follow the on-screen instructions.
2. Start the engine.
Dose the engine start?
YES
>> Inspection End.
NO
>> GO TO 2.
2.
CHECK DONGLE UNIT CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector and dongle unit connector.
3. Check continuity between BCM harness connector and dongle unit harness connector.
4. Check continuity between BCM harness connector and ground.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2196
DONGLE NG
The ID verification results between BCM
and dongle unit is NG.
• Harness or connectors
(Dongle unit circuit is open or shorted.)
• Dongle unit
BCM
Dongle unit
Continuity
Connector
Terminal
Connector
Terminal
M18
16
M5
1
Yes
2015 Rogue NAM
SEC-174
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
B2196 DONGLE UNIT
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK DONGLE UNIT GROUND CIRCUIT
Check continuity between dongle unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace dongle unit.
NO
>> Repair or replace harness.
BCM
Ground
Continuity
Connector
Terminal
M18
16
No
Dongle unit
Ground
Continuity
Connector
Terminal
M5
4
Yes
2015 Rogue NAM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст