Nissan Rogue. Instruction — part 1099
B2198 NATS ANTENNA AMP.
SEC-175
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2198 NATS ANTENNA AMP.
DTC Logic
INFOID:0000000011278588
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Make the conditions that BCM enters in the low power consumption mode (BCM sleep condition).
BCS-84, "POWER CONSUMPTION CONTROL SYSTEM : System Description"
2. Turn ignition switch ON.
3. Check DTC in “Self Diagnostic Result” of “BCM” using CONSULT.
Is DTC detected?
YES
>> Go to
SEC-175, "Diagnosis Procedure"
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011278589
Regarding Wiring Diagram information, refer to
1.
CHECK FUSE
1. Turn power switch OFF.
2. Check that the following fuse in fuse block (J/B) is not blown.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the blown fuse after repairing the affected circuit.
2.
CHECK NATS ANTENNA AMP. POWER SUPPLY
1. Disconnect NATS antenna amp. connector.
2. Check voltage between NATS antenna amp. harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 3.
3.
CHECK NATS ANTENNA AMP. POWER SUPPLY CIRCUIT
1. Disconnect fuse block (J/B) connector.
2. Check continuity between fuse block (J/B) harness connector and NATS antenna amp. connector.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2198
NATS ANTENNA AMP
Inactive communication between NATS
antenna amp. and BCM is detected when
BCM enters in the low power consumption
mode. (BCM sleep condition)
• Harness or connectors
(NATS antenna amp. circuit is open or
shorted.)
• NATS antenna amp.
• BCM
Signal name
Fuse No.
Battery power supply
9 (5 A)
(+)
(–)
Voltage (V)
(Approx.)
NATS antenna amp.
Connector
Terminal
M4
3
Ground
Battery voltage
2015 Rogue NAM
SEC-176
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
B2198 NATS ANTENNA AMP.
Is the inspection result normal?
YES
>> Replace fuse block (J/B).
NO
>> Repair or replace harness.
4.
CHECK NATS ANTENNA AMP. GROUND CIRCUIT
Check continuity between NATS antenna amp. harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK NATS ANTENNA AMP. COMMUNICATION SIGNAL 1
Check voltage signal between NATS antenna amp. harness connector and ground using an oscilloscope.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> GO TO 6.
6.
CHECK NATS ANTENNA AMP. OUTPUT SIGNAL CIRCUIT 1
1. Disconnect BCM connector.
2. Check continuity between NATS antenna amp. harness connector and BCM connector.
3. Check continuity between NATS antenna amp. harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Repair or replace harness.
7.
CHECK NATS ANTENNA AMP. COMMUNICATION SIGNAL 2
Fuse block (J/B)
NATS antenna amp.
Continuity
Connector
Terminal
Connector
Terminal
M44
12 R
M4
3
Yes
NATS antenna amp.
Ground
Continuity
Connector
Terminal
M4
2
Yes
(+)
(–)
Condition
Voltage (V)
(Approx.)
NATS antenna amp.
Connector
Terminal
M4
1
Ground
Key: Key battery is re-
moved
Brake pedal: Depressed
NOTE:
Waveform varies each time
when brake pedal is depressed.
Brake pedal: Not depressed
Battery voltage
JMKIA6232JP
NATS antenna amp.
BCM
Continuity
Connector
Terminal
Connector
Terminal
M4
1
M19
109
Yes
NATS antenna amp.
Ground
Continuity
Connector
Terminal
M4
1
No
2015 Rogue NAM
B2198 NATS ANTENNA AMP.
SEC-177
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Check voltage signal between NATS antenna amp. harness connector and ground using an oscilloscope.
Is the inspection result normal?
YES
>> Replace NATS antenna amp. Refer to
SEC-195, "Removal and Installation"
.
NO
>> GO TO 8.
8.
CHECK NATS ANTENNA AMP. OUTPUT SIGNAL CIRCUIT 2
1. Disconnect BCM connector.
2. Check continuity between NATS antenna amp. harness connector and BCM connector.
3. Check continuity between NATS antenna amp. harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Repair or replace harness.
9.
REPLACE BCM
1. Replace BCM. Refer to
BCS-135, "Removal and Installation"
.
2. Perform initialization of BCM and registration of all keys using CONSULT.
>> Inspection End
(+)
(–)
Condition
Voltage (V)
(Approx.)
NATS antenna amp.
Connector
Terminal
M4
4
Ground
Key: Key battery is re-
moved
Brake pedal: Depressed
NOTE:
Waveform varies each time
when brake pedal is de-
pressed.
Brake pedal: Not depressed
Battery voltage
JMKIA6233JP
NATS antenna amp.
BCM
Continuity
Connector
Terminal
Connector
Terminal
M4
4
M19
113
Yes
NATS antenna amp.
Ground
Continuity
Connector
Terminal
M4
4
No
2015 Rogue NAM
SEC-178
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
B2608 STARTER RELAY
B2608 STARTER RELAY
DTC Logic
INFOID:0000000011278590
DTC DETECTION LOGIC
NOTE:
• If DTC B2608 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B2608 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
• If DTC B2608 is displayed with other DTC (BCM), first perform the trouble diagnosis for other DTC detected.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Press push-button ignition switch under the following conditions to start engine:
-
Selector lever: In the P position
-
Brake pedal: Depressed
2. Wait 1 second after engine started.
3. Check DTC in “Self Diagnostic Result” of “BCM” using CONSULT.
Is DTC detected?
YES
>> Go to
SEC-178, "Diagnosis Procedure"
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000011278591
1.
CHECK DTC OF IPDM E/R
Select “Self Diagnostic Result” of “IPDM E/R” using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
NO
>> GO TO 2.
2.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace BCM. Refer to
BCS-75, "Removal and Installation"
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2608
STARTER RELAY
BCM outputs starter relay OFF signal but
BCM receives starter relay ON signal from
IPDM E/R (CAN).
• Harness or connectors
(The CAN communication line is open or
shorted.)
• Harness or connectors
(Starter relay circuit is open or shorted.)
• IPDM E/R
• Starter relay
2015 Rogue NAM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст