Nissan Titan A60. Instruction — part 471
OIL SEAL
EM-69
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
OIL SEAL
Removal and Installation of Valve Oil Seal
INFOID:0000000006179408
REMOVAL
1. Remove the camshaft relating to the valve oil seal to be removed. Refer to
2. Remove the valve lifters. Refer to
• Correctly identify the location where each part is removed from. Keep parts organized to avoid mixing
them up.
3. Turn the crankshaft until the cylinder requiring new oil seals is at TDC. This will prevent the valve from
dropping into the cylinder.
4. Remove the valve collet using Tool.
CAUTION:
Do not damage the valve lifter holes.
5. Remove the valve spring retainer and valve spring.
CAUTION:
Do not remove the valve spring seat from the valve spring.
6. Remove the valve oil seal using Tool.
INSTALLATION
Installation is in the reverse order of removal.
• Install the valve oil seal using Tool.
• Apply new engine oil on the new valve oil seal joint and seal lip.
• Install the valve oil seal to the specified height "H".
Removal and Installation of Front Oil Seal
INFOID:0000000006179409
REMOVAL
1. Remove the drive belt. Refer to
EM-13, "Removal and Installation"
.
2. Remove radiator. Refer to
CO-16, "Removal and Installation"
3. Remove drive plate cover.
Tool number
: KV10116200 (J-26336-A)
: KV10115900 (J-26336-20)
: KV10109220 ( — )
WBIA0578E
Tool number
: KV10107902 (J-38959)
WBIA0478E
Tool number
: KV10115600 (J-38958)
Height "H" (without valve spring installed)
Intake and exhaust
: 14.300 - 14.900 mm (0.5630 -
0.5870 in)
WBIA0490E
EM-70
< REMOVAL AND INSTALLATION >
OIL SEAL
4. Lock crankshaft using Tool (A).
5. Matchmark crankshaft pulley bolt flange and crankshaft pulley for installation.
6. Remove the crankshaft pulley bolt and crankshaft pulley from
the crankshaft using suitable tool.
7. Remove the front oil seal using suitable tool.
CAUTION:
Do not damage front cover and oil pump drive spacer.
INSTALLATION
1. Apply new engine oil to both the oil seal lip and dust seal lip of the new front oil seal.
2. Install the front oil seal.
• Install the front oil seal so that each seal lip is oriented as
shown.
Tool number
: — (J-47245)
LBIA0455E
KBIA2477E
SBIA0359E
SEM715A
OIL SEAL
EM-71
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Press-fit until the height of the front oil seal is level with the
mounting surface using suitable tool.
CAUTION:
• Do not damage front timing chain case and crankshaft.
• Press-fit straight and avoid causing burrs or tilting of the
oil seal.
3. Apply engine oil onto the threaded parts of the crankshaft pulley bolt and seating area.
4. Align the matchmark on the crankshaft pulley bolt flange and the
crankshaft pulley, install crankshaft pulley and tighten bolt to
specifications using Tool.
5. Remove Tool (A).
6. Installation of the remaining components is in the reverse order of removal.
Removal and Installation of Rear Oil Seal
INFOID:0000000006179410
REMOVAL
1. Remove the transmission assembly. Refer to
TM-206, "Removal and Installation (2WD)"
"Removal and Installation (4WD)"
.
2. Before removing the drive plate, put a match mark (A) on the
crankshaft and drive plate for alignment during installation
3. Remove the drive plate.
PBIC2931E
Crankshaft pulley bolt torque
Step 1
: 93.1 N·m (9.5 kg-m, 69 ft-lb)
Step 2
: additional 90
° (angle tightening)
Tool number
: KV10112100 (BT-8653-A)
KBIA2519E
Tool number
: — (J-47245)
LBIA0455E
ALBIA0522ZZ
EM-72
< REMOVAL AND INSTALLATION >
OIL SEAL
• Holding the crankshaft pulley bolt, lock the crankshaft to
remove the drive plate bolts.
• Remove drive plate bolts diagonally.
CAUTION:
• Do not damage the drive plate. Especially, avoid deform-
ing and damaging the signal plate teeth (circumference
position).
• Keep magnetic materials away from signal plate.
• Place the drive plate with the signal plate surface facing
upward.
4. Remove the rear oil seal using suitable tool.
CAUTION:
Do not damage crankshaft or oil seal retainer surface.
INSTALLATION
1. Apply new engine oil to both the oil seal lip and dust seal lip of the new rear oil seal.
2. Install the rear oil seal.
• Install the rear oil seal so that each seal lip is oriented as
shown.
- A: Oil seal lip
- B: Dust seal lip
-
: Engine inside
-
: Engine outside
• Press in rear oil seal (1) to the position as shown.
- B: Rear oil seal retainer rear end face
- a: 0 - 0.5 mm (0 - 0.020 in)
KBIA2491E
WBIA0437E
JPBIA0054ZZ
JPBIA0152ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст