Nissan Titan A60. Instruction — part 298
PROPELLER SHAFT
DLN-131
< REMOVAL AND INSTALLATION >
[PROPELLER SHAFT: 2F1310]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
REMOVAL AND INSTALLATION
PROPELLER SHAFT
On-Vehicle Service
INFOID:0000000006179517
APPEARANCE AND NOISE INSPECTION
• Check the propeller shaft tube surface for dents or cracks. If damaged, replace the propeller shaft assembly.
• Check the bearings for noise and damage. Repair or replace the bearings as necessary.
PROPELLER SHAFT VIBRATION
If a vibration is present at high speed, inspect the propeller shaft runout first.
1. Measure the runout of the propeller shaft tube at several points
by rotating the final drive companion flange with your hands.
DLN-136, "General Specification"
.
2. If the runout exceeds specifications, disconnect the propeller
shaft at the final drive companion flange; then rotate the com-
panion flange 90
°, 180° and 270° and reconnect the propeller
shaft.
3. Check the runout again. If the runout still exceeds specifications,
replace the propeller shaft assembly. Refer to
.
4. After installation, check for vibration by driving the vehicle.
LDIA0160E
LDIA0118E
DLN-132
< UNIT REMOVAL AND INSTALLATION >
[PROPELLER SHAFT: 2F1310]
PROPELLER SHAFT
UNIT REMOVAL AND INSTALLATION
PROPELLER SHAFT
Removal and Installation
INFOID:0000000006179518
COMPONENTS
REMOVAL
1. Put matching marks on the front propeller shaft flange yoke and
the front final drive companion flange as shown.
CAUTION:
For matching marks, use paint. Never damage the flange
yoke and companion flange of the front final drive.
2. Put matching marks on the front propeller shaft flange yoke and
the transfer companion flange.
CAUTION:
For matching marks, use paint. Never damage the flange
yoke and companion flange of the front final drive.
3. Remove the bolts and then remove the front propeller shaft from
the front final drive and transfer.
INSPECTION
1.
Propeller shaft tube
2.
Snap ring
3.
Journal bearing
4.
Journal
5.
Flange yoke
Front
WDIA0304E
SDIA2046E
PROPELLER SHAFT
DLN-133
< UNIT REMOVAL AND INSTALLATION >
[PROPELLER SHAFT: 2F1310]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• Inspect the propeller shaft runout. If runout exceeds the limit,
replace the propeller shaft assembly. Refer to
• While holding the flange yoke on one side, check axial play of the
joint as shown. If the journal axial play exceeds the specification,
repair or replace the journal parts. Refer to
• Check the propeller shaft tube surface for dents or cracks. If dam-
age is detected, replace the propeller shaft assembly.
INSTALLATION
Installation is in the reverse order of removal.
• After installation, check for vibration by driving the vehicle. Refer to
DLN-130, "NVH Troubleshooting Chart"
.
CAUTION:
Do not reuse the bolts and nuts. Always install new ones.
LDIA0118E
LDIA0117E
DLN-134
< UNIT DISASSEMBLY AND ASSEMBLY >
[PROPELLER SHAFT: 2F1310]
PROPELLER SHAFT
UNIT DISASSEMBLY AND ASSEMBLY
PROPELLER SHAFT
Disassembly and Assembly
INFOID:0000000006179519
DISASSEMBLY
Journal
1. Put matching marks on the front propeller shaft and flange yoke
as shown.
CAUTION:
For matching marks, use paint. Never damage the front pro-
peller shaft or flange yoke.
2. Remove the snap rings.
3. Push out and remove the journal bearings by lightly tapping the
flange yoke with a hammer, taking care not to damage the jour-
nal or flange yoke hole.
NOTE:
Put marks on the disassembled parts so that they can be rein-
stalled in their original positions from which they were removed.
4. Push out and remove the remaining journal bearings at the
opposite side by lightly tapping the flange yoke with a hammer,
taking care not to damage the journal or flange yoke hole.
NOTE:
Put marks on the disassembled parts so that they can be rein-
stalled in their original positions from which they were removed.
ASSEMBLY
SPD128
APD011
SPD732
SPD131
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст