Nissan Titan A60. Instruction — part 896
HYDRAULIC LINE
ST-21
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
• Confirm mating marks are aligned with hose and clamp, then cor-
rect if needed.
• To install eye joint, align projection of eye joint with notch of power
steering pump, and attach eye joint to power steering oil pump
properly. Tighten eye bolt by hand fully, then torque to specifica-
tion.
SGIA0563E
WGIA0089E
ST-22
< UNIT DISASSEMBLY AND ASSEMBLY >
STEERING COLUMN
UNIT DISASSEMBLY AND ASSEMBLY
STEERING COLUMN
Disassembly and Assembly
INFOID:0000000006164507
Column Shift Model
CAUTION:
• Any time the ignition switch has been disconnected, removed or installed, the keys must be re-regis-
tered in the BCM. Refer to Consult-III operations IVIS/NVIS.
• Care must be taken not to give axial impact to steering column assembly during removal and instal-
lation.
• Care must be taken not to move power steering gear during removal of steering column assembly.
WGIA0085E
1.
Steering column assembly
2. Ignition switch
3.
Upper joint
4.
Spring
5. Tilt lever knob
6.
Self-shear screw
STEERING COLUMN
ST-23
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
Floor Shift Model
CAUTION:
• Any time the ignition switch has been disconnected, removed or installed, the keys must be re-regis-
tered in the BCM. Refer to Consult-III operations IVIS/NVIS.
• Care must be taken not to give axial impact to steering column assembly during removal and instal-
lation.
• Care must be taken not to move power steering gear during removal of steering column assembly.
DISASSEMBLY
1. Remove spring from steering column assembly and tilt lever.
2. Remove upper joint bolt, then remove upper joint from steering column assembly.
3. Remove ignition switch tamper resistant self-shear type screws with a drill or other appropriate tool.
ASSEMBLY
• Assembly is in the reverse order of disassembly.
• Install new tamper resistant self-shear type screws.
• Any time the ignition switch has been disconnected, removed or
installed, the keys must be re-registered in the BCM. Refer to Con-
sult-III operations IVIS/NVIS.
INSPECTION AFTER ASSEMBLY
WGIA0088E
1.
Steering column assembly
2. Ignition switch
3.
Upper joint
4.
Spring
5. Tilt lever knob
6.
Self-shear screw
WGIA0009E
ST-24
< UNIT DISASSEMBLY AND ASSEMBLY >
STEERING COLUMN
When the steering wheel does not turn smoothly, check the steering column as follows:
1. Check the column bearings for damage or unevenness. Lubricate with recommended multi-purpose
grease. Replace the steering column as an assembly, if necessary.
2. Check the column tube for deformation or breakage. Replace the steering column as an assembly, if nec-
essary.
3. If the vehicle has been involved in a collision, or if noise and rattles are heard during a turn, check the
length (L) of the column. If out of specification, replace the steering column as an assembly.
4. Check for proper lubrication, apply grease as necessary.
5. Check for wear around the seal edges, replace as necessary.
6. Check for corrosion or pitting around the seal sliding area.
7. Replace the seal and shaft in case of seal edge wear or damage.
8. After installing the steering column, check the tilt mechanism for proper operation.
Steering column length L
L
L
1
L
2
WGIA0080E
SGIA0475E
Range (A)
: Refer to
WGIA0083E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст