Nissan Titan A60. Instruction — part 925
TM-88
< DTC/CIRCUIT DIAGNOSIS >
P1757 FRONT BRAKE SOLENOID
P1757 FRONT BRAKE SOLENOID
Description
INFOID:0000000006159369
Front brake solenoid valve is controlled by the TCM in response to signals sent from the transmission range
switch, output speed sensor and accelerator pedal position sensor (throttle position sensor). Gears will then
be shifted to the optimum position.
CONSULT-III Reference Value in Data Monitor Mode
INFOID:0000000006159370
On Board Diagnosis Logic
INFOID:0000000006159371
• This is an OBD-II self-diagnostic item.
• Diagnostic trouble code “P1757” with CONSULT-III or 6th judgment flicker without CONSULT-III is detected
under the following conditions.
- When TCM detects an improper voltage drop when it tries to operate the solenoid valve.
- When TCM detects as irregular by comparing target value with monitor value.
Possible Cause
INFOID:0000000006159372
• Harness or connectors
(The solenoid circuit is open or shorted.)
• Front brake solenoid valve
DTC Confirmation Procedure
INFOID:0000000006159373
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-III
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
3. Start engine.
4. Drive vehicle and maintain the following conditions for at least 5 consecutive seconds.
ACCELE POSI: 1.5/8 - 2.0/8
SLCT LVR POSI: “D” position
GEAR: 3rd
⇒ 4th (FR/B ON/OFF)
Driving location: Driving the vehicle uphill (increased engine load) will help maintain the driving
conditions required for this test.
5. If DTC is detected go to
.
WITH GST
Follow the procedure “With CONSULT-III”.
Diagnosis Procedure
INFOID:0000000006159374
1.
CHECK INPUT SIGNAL
With CONSULT-III
1. Turn ignition switch “ON”.
2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
3. Start engine.
4. Read out the value of “FR/B SOLENOID” while driving.
Item name
Condition
Display value (Approx.)
FR/B SOLENOID
Front brake engaged. Refer to
0.6 - 0.8 A
Front brake disengaged. Refer to
0 - 0.05 A
P1757 FRONT BRAKE SOLENOID
TM-89
< DTC/CIRCUIT DIAGNOSIS >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 2.
2.
CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace damaged parts.
3.
DETECT MALFUNCTIONING ITEM
Check the following items:
• The A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> Replace the control valve with TCM. Refer to
TM-197, "Control Valve with TCM"
NG
>> Repair or replace damaged parts.
4.
CHECK DTC
Perform “DTC Confirmation Procedure”.
• Refer to
TM-88, "DTC Confirmation Procedure"
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 2.
Item name
Condition
Display value (Approx.)
FR/B SOLENOID
0.6 - 0.8 A
Front brake disengaged. Refer to
0 - 0.05 A
TM-90
< DTC/CIRCUIT DIAGNOSIS >
P1762 DIRECT CLUTCH SOLENOID
P1762 DIRECT CLUTCH SOLENOID
Description
INFOID:0000000006159375
Direct clutch solenoid valve is controlled by the TCM in response to signals sent from the transmission range
switch, output speed sensor and accelerator pedal position sensor (throttle position sensor). Gears will then
be shifted to the optimum position.
CONSULT-III Reference Value in Data Monitor Mode
INFOID:0000000006159376
On Board Diagnosis Logic
INFOID:0000000006159377
• This is an OBD-II self-diagnostic item.
• Diagnostic trouble code “P1762” with CONSULT-III or 2nd judgment flicker without CONSULT-III is detected
under the following conditions.
- When TCM detects an improper voltage drop when it tries to operate the solenoid valve.
- When TCM detects as irregular by comparing target value with monitor value.
Possible Cause
INFOID:0000000006159378
• Harness or connectors
(The solenoid circuit is open or shorted.)
• Direct clutch solenoid valve
DTC Confirmation Procedure
INFOID:0000000006159379
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-III
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
3. Start engine.
4. Drive vehicle and maintain the following conditions for at least 5 consecutive seconds.
ACCELE POSI: 1.5/8 - 2.0/8
SLCT LVR POSI: “D” position
GEAR: 1st
⇒ 2nd (D/C ON/OFF)
Driving location: Driving the vehicle uphill (increased engine load) will help maintain the driving
conditions required for this test.
5. If DTC is detected, go to
WITH GST
Follow the procedure “With CONSULT-III”.
Diagnosis Procedure
INFOID:0000000006159380
1.
CHECK INPUT SIGNAL
With CONSULT-III
1. Turn ignition switch “ON”.
2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
3. Start the engine.
4. Read out the value of “D/C SOLENOID” while driving.
Item name
Condition
Display value (Approx.)
D/C SOLENOID
Direct clutch disengaged. Refer to
0.6 - 0.8 A
Direct clutch engaged. Refer to
0 - 0.05 A
P1762 DIRECT CLUTCH SOLENOID
TM-91
< DTC/CIRCUIT DIAGNOSIS >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OK or NG
OK
>> GO TO 4.
NG
>> GO TO 2.
2.
CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace damaged parts.
3.
DETECT MALFUNCTIONING ITEM
Check the following items:
• The A/T assembly harness connector pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> Replace the control valve with TCM. Refer to
TM-197, "Control Valve with TCM"
NG
>> Repair or replace damaged parts.
4.
CHECK DTC
Perform “DTC Confirmation Procedure”.
• Refer to
TM-90, "DTC Confirmation Procedure"
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 2.
Item name
Condition
Display value (Approx.)
D/C SOLENOID
Direct clutch disengaged. Refer to
0.6 - 0.8 A
Direct clutch engaged. Refer to
0 - 0.05 A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст