Nissan Note E12. Instruction — part 670
TM-238
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
OIL PAN
OIL PAN
Exploded View
INFOID:0000000009020033
Removal and Installation
INFOID:0000000009020034
REMOVAL
1. Remove the drain plug and overflow tube, and then drain the CVT fluid.
WARNING:
CVT fluid can splash when draining, use safety glasses to protect eyes.
2. Remove the drain plug gasket from the drain plug.
3. Remove the oil pan bolts (
), and then remove the oil pan and
oil pan gasket.
4. Remove the magnets from the oil pan.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse oil pan gasket and drain plug gasket.
1.
Transaxle assembly
2.
Oil pan gasket
3.
Magnet
4.
Oil pan
5.
Overflow tube
6.
Drain plug gasket
7.
Drain plug
8.
Oil pan fitting bolt
JSDIA1879GB
: Front
JSDIA1874ZZ
OIL PAN
TM-239
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• Do not reuse oil pan bolts.
• Completely remove all moisture, oil and old gasket, etc. from the oil pan gasket mating surface of
transaxle case and oil pan.
• When installing the overflow tube, be sure to tighten to the specified torque. If it is not tightened to
the specified torque, the tube may be damaged.
• When the oil pan is installed, temporarily tighten oil pan bolts, then
tighten the oil pan bolts to specification in the order shown.
Inspection and Adjustment
INFOID:0000000009020035
INSPECTION AFTER REMOVAL
Check oil pan for foreign material.
• If a large amount of worn material is found, clutch plate may be worn.
• If iron powder is found, bearings, gears, or clutch plates may be worn.
• If aluminum powder is found, bushing may be worn, or chips or burrs of aluminum casting parts may enter.
Check points where wear is found in all cases.
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage. Refer to
.
ADJUSTMENT AFTER INSTALLATION
Check the CVT fluid level. Refer to
: Front
JSDIA1884ZZ
TM-240
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
PRIMARY SPEED SENSOR
PRIMARY SPEED SENSOR
Exploded View
INFOID:0000000009020036
Removal and Installation
INFOID:0000000009020037
REMOVAL
1. Partially remove fender protector (LH). Refer to
EXT-24, "Removal and Installation"
2. Disconnect the harness connector from primary speed sensor.
3. Remove the primary speed sensor.
4. Remove the O-ring from the primary speed sensor.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-ring.
• Apply Genuine NISSAN CVT Fluid NS-3 to the O-ring.
Inspection and Adjustment
INFOID:0000000009020038
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage. Refer to
.
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT fluid level. Refer to
.
1.
Transaxle assembly
2.
O-ring
3.
Primary speed sensor
Front
: Genuine NISSAN CVT Fluid NS-3
JSDIA1880GB
SECONDARY SPEED SENSOR
TM-241
< REMOVAL AND INSTALLATION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SECONDARY SPEED SENSOR
Exploded View
INFOID:0000000009020039
Removal and Installation
INFOID:0000000009020040
REMOVAL
1. Remove battery tray. Refer to
PG-70, "Removal and Installation (Battery Tray)"
2. Remove IPDM/ER. Refer to
PCS-30, "Removal and Installation"
3. Disconnect the harness connector from secondary speed sensor.
4. Remove the secondary speed sensor.
5. Remove the O-ring from the secondary speed sensor.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-ring.
• Apply Genuine NISSAN CVT Fluid NS-3 to the O-ring.
Inspection and Adjustment
INFOID:0000000009020041
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage. Refer to
.
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT fluid level. Refer to
.
1.
Transaxle assembly
2.
O-ring
3.
Secondary speed sensor
Front
: Genuine NISSAN CVT Fluid NS-3
JSDIA1881GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст