Nissan Note E12. Instruction — part 564
SEC-108
< DTC/CIRCUIT DIAGNOSIS >
B210B STARTER CONTROL RELAY
B210B STARTER CONTROL RELAY
DTC Logic
INFOID:0000000009567462
DTC DETECTION LOGIC
NOTE:
If DTC B210B is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION
1. Turn ignition switch ON.
2. Turn ignition switch OFF and wait 1 second or more.
3. Turn ignition switch ON.
4. Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is DTC B210B displayed?
YES
>> Refer to
SEC-108, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009567463
1.
PERFORM SELF DIAGNOSTIC RESULT
Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is display history of DTC B210B CRNT?
YES
>> Replace IPDM E/R. Refer to
PCS-30, "Removal and Installation"
NO
>> Refer to
GI-41, "Intermittent Incident"
.
CONSULT Display
DTC Detection Condition
Possible Cause
START CONT RLY ON
[B210B]
When comparing the following items, IPDM E/R
detects that starter control relay is stuck in the
ON position for 1 second or more.
• Starter control relay signal (CAN) from BCM
• Starter relay status signal (CAN) from BCM
• Starter control relay and starter relay status
signal (IPDM E/R input)
• Starter control relay control signal (IPDM E/R
output)
• Transmission range switch signal input
IPDM E/R
B210C STARTER CONTROL RELAY
SEC-109
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B210C STARTER CONTROL RELAY
DTC Logic
INFOID:0000000009567464
DTC DETECTION LOGIC
NOTE:
• If DTC B210C is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• When IPDM E/R power supply voltage is low (Approx. 7 - 8 V for about 1 second), the DTC B210C may be
detected.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION
1. Turn ignition switch ON.
2. Turn ignition switch OFF and wait 1 second or more.
3. Turn ignition switch ON.
4. Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is DTC B210C displayed?
YES
>> Refer to
SEC-109, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009567465
Regarding Wiring Diagram information, refer to
.
1.
PERFORM SELF DIAGNOSTIC RESULT
Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is display history of DTC B210C CRNT?
YES
>> GO TO 2.
NO
>> Refer to
GI-41, "Intermittent Incident"
.
2.
CHECK STARTER CONTROL RELAY CONTROL CIRCUITS VOLTAGE
Check voltage between IPDM E/R connectors and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-30, "Removal and Installation"
.
NO (WITH M/T)>>GO TO 3.
NO (WITH CVT)>>GO TO 4.
CONSULT Display
DTC Detection Condition
Possible Cause
STR CONT RLY OFF CIRC
[B210C]
When comparing the following items, IPDM E/R
detects that starter control relay is stuck in the
OFF position for 1 second or more.
• Starter control relay signal (CAN) from BCM
• Starter relay status signal (CAN) from BCM
• Starter control relay and starter relay status
signal (IPDM E/R input)
• Starter control relay control signal (IPDM E/R
output)
• IPDM E/R
• BCM
• Battery
IPDM E/R
Ground
Voltage
(Approx.)
Connector
Terminal
E44 (WITH M/T)
13
—
Battery voltage
F42 (WITH CVT)
40
SEC-110
< DTC/CIRCUIT DIAGNOSIS >
B210C STARTER CONTROL RELAY
3.
CHECK STARTER CONTROL RELAY CONTROL CIRCUIT CONTINUITY
1. Disconnect IPDM E/R connector E44 and clutch interlock switch connector E34.
2. Check continuity between IPDM E/R connector E44 and clutch interlock switch connector E34.
3. Disconnect BCM connector M98.
4. Check continuity between IPDM E/R connector E44 and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-67, "Removal and Installation"
NO
>> Repair or replace harness or connectors.
4.
CHECK STARTER CONTROL RELAY CONTROL CIRCUIT CONTINUITY
1. Disconnect IPDM E/R connector F42 and transmission range switch connector F52.
2. Check continuity between IPDM E/R connector F42 and transmission range switch connector F52.
3. Disconnect BCM connector M98.
4. Check continuity between IPDM E/R connector F42 and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-67, "Removal and Installation"
NO
>> Repair or replace harness or connectors.
IPDM E/R
Clutch interlock switch
Continuity
Connector
Terminal
Connector
Terminal
E44
13
E34
2
Yes
IPDM E/R
Ground
Continuity
Connector
Terminal
E44
13
—
No
IPDM E/R
Transmission range switch
Continuity
Connector
Terminal
Connector
Terminal
F42
40
F52
10
Yes
IPDM E/R
Ground
Continuity
Connector
Terminal
F42
40
—
No
B210D STARTER RELAY
SEC-111
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B210D STARTER RELAY
DTC Logic
INFOID:0000000009567466
DTC DETECTION LOGIC
NOTE:
If DTC B210D is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION
1. Turn ignition switch ON.
2. Turn ignition switch OFF and wait 1 second or more.
3. Turn ignition switch ON.
4. Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is DTC B210D displayed?
YES
>> Refer to
SEC-111, "Diagnosis Procedure"
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009567467
Regarding Wiring Diagram information, refer to
.
1.
PERFORM SELF DIAGNOSTIC RESULT
Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is display history of DTC B210D CRNT?
YES
>> GO TO 2.
NO
>> Refer to
GI-41, "Intermittent Incident"
.
2.
CHECK STARTER CONTROL RELAY CONTROL CIRCUITS VOLTAGE
Check voltage between IPDM E/R connectors and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-30, "Removal and Installation"
.
NO (WITH M/T)>>GO TO 3.
NO (WITH CVT)>>GO TO 4.
3.
CHECK STARTER CONTROL RELAY CONTROL CIRCUIT CONTINUITY
1. Disconnect IPDM E/R connectors E44, BCM connector M98, clutch interlock switch connector E34.
CONSULT Display
DTC Detection Condition
Possible Cause
STARTER RLY ON CIRC
[B210D]
When comparing the following items, IPDM E/R
detects that starter control relay is stuck in the
ON position for 5 second or more.
• Starter control relay signal (CAN) from BCM
• Starter relay status signal (CAN) from BCM
• Starter control relay and starter relay status
signal (IPDM E/R input)
• Starter control relay control signal (IPDM E/R
output)
• Harness or connectors (starter motor relay
control circuit open or short)
• IPDM E/R
• BCM
IPDM E/R
Ground
Voltage
(Approx.)
Connector
Terminal
E44
13
—
Battery voltage
F42
40
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст