Nissan Note E12. Instruction — part 565
SEC-112
< DTC/CIRCUIT DIAGNOSIS >
B210D STARTER RELAY
2. Check continuity between IPDM E/R connector E44 and ground.
Is the inspection result normal?
YES
>> Refer to
.
NO
>> Repair or replace harness or connectors.
4.
CHECK STARTER CONTROL RELAY CONTROL CIRCUIT CONTINUITY
1. Disconnect IPDM E/R connectors F42, BCM connector M98, transmission range switch connector F52.
2. Check continuity between IPDM E/R connector F42 and ground.
Is the inspection result normal?
YES
>> Refer to
.
NO
>> Repair or replace harness or connectors.
IPDM E/R
Ground
Continuity
Connector
Terminal
E44
13
—
No
IPDM E/R
Ground
Continuity
Connector
Terminal
F42
40
—
No
B210E STARTER RELAY
SEC-113
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B210E STARTER RELAY
DTC Logic
INFOID:0000000009567469
DTC DETECTION LOGIC
NOTE:
• If DTC B210E is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B210E is displayed with DTC B2605, first perform the trouble diagnosis for DTC B2605. Refer to
• When IPDM E/R power supply voltage is low (Approx. 7 - 8 V for about 1 second), the DTC B210F may be
detected.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION
1. Turn ignition switch ON.
2. Turn ignition switch OFF and wait 1 second or more.
3. Turn ignition switch ON.
4. Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is DTC B210E displayed?
YES
>> Refer to
SEC-113, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009567470
Regarding Wiring Diagram information, refer to
.
1.
PERFORM SELF DIAGNOSTIC RESULT
Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is display history of DTC B210E CRNT?
YES
>> GO TO 2.
NO
>> Refer to
GI-41, "Intermittent Incident"
.
2.
CHECK STARTER CONTROL RELAY CONTROL CIRCUITS VOLTAGE
Check voltage between IPDM E/R connectors and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-30, "Removal and Installation"
.
NO (WITH M/T)>>GO TO 3.
CONSULT Display
DTC Detection Condition
Possible Cause
STARTER RELAY OFF
[B210E]
When comparing the following items, IPDM E/R
detects that starter control relay is stuck in the
OFF position for 5 second or more.
• Starter control relay signal (CAN) from BCM
• Starter relay status signal (CAN) from BCM
• Starter control relay and starter relay status
signal (IPDM E/R input)
• Starter control relay control signal (IPDM E/R
output)
• IPDM E/R
• BCM
• Battery
IPDM E/R
Ground
Voltage
(Approx.)
Connector
Terminal
E44
13
—
Battery voltage
F42
40
SEC-114
< DTC/CIRCUIT DIAGNOSIS >
B210E STARTER RELAY
NO (WITH CVT)>>GO TO 4.
3.
CHECK STARTER CONTROL RELAY CONTROL CIRCUIT CONTINUITY
1. Disconnect IPDM E/R connector E44 and clutch interlock switch connector E34.
2. Check continuity between IPDM E/R connector E44 and clutch interlock switch connector E34.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-67, "Removal and Installation"
NO
>> Repair or replace harness or connectors.
4.
CHECK STARTER CONTROL RELAY CONTROL CIRCUIT CONTINUITY
1. Disconnect IPDM E/R connector F42 and transmission range switch connector F52.
2. Check continuity between IPDM E/R connector F42 and transmission range switch connector F52.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-67, "Removal and Installation"
NO
>> Repair or replace harness or connectors.
IPDM E/R
Clutch interlock switch
Continuity
Connector
Terminal
Connector
Terminal
E44
13
E34
2
Yes
IPDM E/R
Transmission range switch
Continuity
Connector
Terminal
Connector
Terminal
F42
40
F52
10
Yes
B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH
SEC-115
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH
DTC Logic
INFOID:0000000009567472
DTC DETECTION LOGIC
NOTE:
If DTC B210F is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Shift selector lever to the P position.
2. Turn ignition switch ON and wait 1 second or more.
3. Shift selector lever to the N position and wait 1 second or more.
4. Shift selector lever to the position other than P and N, and wait 1 second or more.
5. Check DTC in Self Diagnostic Result mode of IPDM E/R using CONSULT.
Is DTC detected?
YES
>> Go to
SEC-115, "Diagnosis Procedure"
.
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009567473
Regarding Wiring Diagram information, refer to
.
1.
CHECK DTC OF BCM
Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
NO
>> GO TO 2.
2.
CHECK IPDM E/R SIGNAL CIRCUIT OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Disconnect transmission range switch connector.
4. Check continuity between IPDM E/R harness connector and transmission range switch harness connec-
tor.
5. Check continuity between IPDM E/R harness connector and ground.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B210F
INTRLCK/PNP SW ON
IPDM E/R detects a difference between the
following signals
• P/N position signal from transmission
range switch and P/N position signal
(CAN) from BCM
• Harness or connectors
(The CAN communication line is open
or shorted.)
• Harness or connectors
(Transmission range switch circuit is
open or shorted.)
• Transmission range switch
• IPDM E/R
• BCM
IPDM E/R
Transmission range switch
Continuity
Connector
Terminal
Connector
Terminal
F42
40
F52
10
Yes
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст