Nissan Note E12. Instruction — part 663
TM-210
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
P285A CLUTCH B PRESSURE
4. Stop the vehicle.
5. Check the first trip DTC.
Is “P285A” detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000009020003
1.
CHECK INTERMITTENT INCIDENT
GI-41, "Intermittent Incident"
Is the inspection result normal?
YES
>> Replace transaxle assembly. Refer to
TM-250, "Removal and Installation"
.
NO
>> Repair or replace malfunctioning parts.
Selector lever
: “L” POSITION
Accelerator pedal position
: 0.7/8 or more
Vehicle speed
: 10 km/h (6 MPH) or more
MAIN POWER SUPPLY AND GROUND CIRCUIT
TM-211
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
MAIN POWER SUPPLY AND GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000009020004
1.
CHECK TCM POWER CIRCUIT (PART 1)
1. Turn ignition switch OFF.
2. Disconnect TCM connector.
3. Check voltage between TCM harness connector terminals and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK TCM POWER CIRCUIT (PART 2)
Check voltage between TCM harness connector terminals and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 5.
3.
CHECK TCM GROUND CIRCUIT
Check continuity between TCM harness connector terminals and ground.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
4.
DETECT MALFUNCTION ITEMS (PART 1)
Check the following items:
• Open circuit or short circuit in harness between battery positive terminal and TCM connectors terminals 45,
and 46.
• 10A fuse (No.33, fuse and fusible link block). Refer to
PG-39, "IPDM E/R Terminal Arrangement"
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
+
−
Voltage
TCM
Connector
Terminal
F44
45
Ground
10 – 16 V
46
+
−
Condition
Voltage
TCM
Connector
Terminal
F44
47
Ground
Ignition switch ON
10 – 16 V
Ignition switch OFF
Approx. 0 V
48
Ignition switch ON
10 – 16 V
Ignition switch OFF
Approx. 0 V
TCM
—
Continuity
Connector
Terminal
F44
41
Ground
Existed
42
TM-212
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
MAIN POWER SUPPLY AND GROUND CIRCUIT
5.
CHECK CIRCUIT BETWEEN IPDM E/R AND TCM
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector terminal and TCM harness connector terminals.
Is the check result normal?
YES
>> GO TO 6.
NO
>> Repair or replace malfunctioning parts.
6.
DETECT MALFUNCTIONING ITEMS (PART 2)
Check the following items:
• Open circuit or short circuit in harness between ignition switch and IPDM E/R. Refer to
gram — Ignition Power Supply —"
• Short circuit in harness between IPDM E/R harness connector terminal 21 and TCM harness connector ter-
minal 47, and 48.
• 10A fuse (No.49, IPDM E/R). Refer to
PG-39, "IPDM E/R Terminal Arrangement"
• IPDM E/R
Is the check result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
IPDM E/R
TCM
Continuity
Connector
Terminal
Connector
Terminal
E45
21
F44
47
Existed
48
OVERDRIVE CONTROL SWITCH
TM-213
< DTC/CIRCUIT DIAGNOSIS >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OVERDRIVE CONTROL SWITCH
Component Function Check
INFOID:0000000009020005
1.
CHECK OD OFF INDICATOR LAMP FUNCTION
Check OD OFF indicator lamp turns ON for approx. 2 seconds when ignition switch turns ON.
Is the inspection results normal?
YES
>> GO TO 2.
NO
>> Go to
2.
CHECK OVERDRIVE CONTROL SWITCH FUNCTION
1. Shift the selector lever to “D” position.
2. Check that OD OFF indicator lamp turns ON/OFF when overdrive control switch is operated.
Is the inspection results normal?
YES
>> INSPECTION END
NO
>> Go to
Diagnosis Procedure
INFOID:0000000009020006
1.
CHECK OVERDRIVE CONTROL SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect CVT shift selector connector.
3. Turn ignition switch ON.
4. Check voltage between CVT shift selector harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK OVERDRIVE CONTROL SWITCH
Check overdrive control switch. Refer to
TM-214, "Component Inspection (Overdrive Control Switch)"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts.
3.
CHECK GROUND CIRCUIT
Check continuity between CVT shift selector harness connector terminal and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace malfunctioning parts.
4.
CHECK CIRCUIT BETWEEN COMBINATION METER AND CVT SHIFT SELECTOR (PART 1)
1. Turn ignition switch OFF.
2. Disconnect combination meter connector.
3. Check continuity between combination meter harness connector terminal and CVT shift selector harness
connector terminal.
CVT shift selector
Voltage
(Approx.)
Connector
+
−
Terminal
M38
1
2
5 V
CVT shift selector
—
Continuity
Connector
Terminal
M38
2
Ground
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст