Nissan Note E12. Instruction — part 382
DOOR CABLE
HAC-51
< REMOVAL AND INSTALLATION >
[MANUAL AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
DOOR CABLE
Exploded View
INFOID:0000000009405618
INTAKE DOOR CABLE
INTAKE DOOR CABLE : Removal and Installation
INFOID:0000000009405619
The intake door cable is not serviced separately. Refer to
HAC-47, "Removal and Installation"
.
INTAKE DOOR CABLE : Adjustment
INFOID:0000000009405620
1. Remove glove box assembly. Refer to
IP-25, "Removal and Installation"
2. Disconnect intake door cable (1) from clip (A).
3. Set intake door lever to REC position.
4. Push intake door link (2) in the direction shown, then carefully
pull outer cable to front air control side and connect clip.
1.
Heating and cooling unit assembly
2.
Plate
3.
Air mix door linkage 2
4.
Air mix door linkage 1
5.
Air mix door cable
6.
Intake door lever
7.
Intake door linkage
8.
Intake door cable
9.
Foot door lever
10. Mode door cable
11. Main linkage
12. Ventilator door rod
13. Ventilator door lever
A.
To front air control
JMIIA1742ZZ
JMIIA0617ZZ
HAC-52
< REMOVAL AND INSTALLATION >
[MANUAL AIR CONDITIONING]
DOOR CABLE
5. Operate intake door lever to make sure that inner cable moves smoothly.
CAUTION:
When clipping outer cable, do not move inner cable.
MODE DOOR CABLE
MODE DOOR CABLE : Removal and Installation
INFOID:0000000009405621
The mode door cable is not serviced separately. Refer to
HAC-47, "Removal and Installation"
.
MODE DOOR CABLE : Adjustment
INFOID:0000000009405622
1. Remove glove box assembly. Refer to
IP-25, "Removal and Installation"
2. Disconnect mode door cable (1) from clip (A).
3. Set mode dial to VENT position.
4. Push main link (2) in the direction shown, then carefully pull
outer cable to front air control side and connect clip.
5. Operate mode dial to make sure that inner cable moves smoothly.
CAUTION:
When clipping outer cable, do not move inner cable.
AIR MIX DOOR CABLE
AIR MIX DOOR CABLE : Removal and Installation
INFOID:0000000009405623
The air mix door cable is not serviced separately. Refer to
HAC-47, "Removal and Installation"
.
AIR MIX DOOR CABLE : Adjustment
INFOID:0000000009405624
1. Remove instrument lower panel LH. Refer to
IP-24, "Removal and Installation"
.
2. Remove foot duct (LH). Refer to
VTL-7, "FOOT DUCT : Removal and Installation"
3. Disconnect air mix door cable (1) from clip (A).
4. Set temperature dial to full cold position.
5. Push air mix door link (2) in the direction shown, then carefully
pull outer cable to front air control side and connect clip.
6. Operate temperature dial to make sure that inner cable moves smoothly.
CAUTION:
When clipping outer cable, do not move inner cable.
JMIIA0618ZZ
JMIIA0619ZZ
HRN-1
DRIVER CONTROLS
C
D
E
F
G
H
I
J
K
M
SECTION
HRN
A
B
HRN
N
O
P
CONTENTS
HORN
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
WIRING DIAGRAM . . . . . . . . . ...
HORN . . . . . . . . . . . . . . . . .
Wiring Diagram . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . .
HORN . . . . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
HRN-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009486656
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Instruction.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст