Nissan Note E12. Instruction — part 381
FRONT AIR CONTROL
HAC-47
< REMOVAL AND INSTALLATION >
[MANUAL AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
REMOVAL AND INSTALLATION
FRONT AIR CONTROL
Exploded View
INFOID:0000000009405613
Removal and Installation
INFOID:0000000009405614
REMOVAL
1. Remove cluster lid C. Refer to
IP-22, "Removal and Installation"
2. Remove front air control finisher. Refer to
IP-23, "Removal and Installation"
3. Remove audio unit or AV control unit. Refer to
AV-33, "Removal and Installation"
AV-178, "Removal and Installation"
(NAVIGATION).
4. Remove air mix door cable, mode door cable, and intake door cable from the heating and cooling unit
assembly.
5. Remove screws and front air control.
INSTALLATION
Installation is in the reverse order of removal.
1.
Front air control
2.
Intake door lever knob
AWIIA1693ZZ
HAC-48
< REMOVAL AND INSTALLATION >
[MANUAL AIR CONDITIONING]
THERMO CONTROL AMPLIFIER
THERMO CONTROL AMPLIFIER
Removal and Installation
INFOID:0000000009645133
REMOVAL
1. Remove evaporator. Refer to
HA-33, "EVAPORATOR : Removal and Installation"
2. Remove thermo control amplifier from evaporator.
INSTALLATION
Installation is in the reverse order of removal.
REFRIGERANT PRESSURE SENSOR
HAC-49
< REMOVAL AND INSTALLATION >
[MANUAL AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
REFRIGERANT PRESSURE SENSOR
Removal and Installation
INFOID:0000000009515775
CAUTION:
Perform lubricant return operation before each A/C system disassembly. However, if a large amount of
refrigerant or lubricant leaks from the system, do not perform lubricant return operation. Refer to
21, "Perform Oil Return Operation"
.
REMOVAL
1. Discharge the refrigerant. Refer to
2. Remove front grille. Refer to
EXT-21, "Removal and Installation"
3. Remove upper air guide and air guide (LH). Refer to
.
4. Clean refrigerant pressure sensor and surrounding area.
CAUTION:
Make sure to clean carefully.
5. Disconnect refrigerant pressure sensor harness connector.
6. Support liquid tank, then remove refrigerant pressure sensor (1).
CAUTION:
• Be careful not to damage liquid tank.
• Be careful not to damage core surface of condenser.
• Cap or wrap the joint of the condenser and liquid tank
with suitable material such as vinyl tape to avoid the entry
of air.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-rings.
• Apply compressor oil to new O-ring of the refrigerant pressure sensor for installation.
• After charging refrigerant, check for leaks. Refer to
.
ALIIA0004ZZ
HAC-50
< REMOVAL AND INSTALLATION >
[MANUAL AIR CONDITIONING]
FRONT BLOWER MOTOR RESISTOR
FRONT BLOWER MOTOR RESISTOR
Exploded View
INFOID:0000000009405616
Removal and Installation
INFOID:0000000009405617
REMOVAL
1. Disconnect harness connector from front blower motor resistor.
2. Remove screws and front blower motor resistor.
INSTALLATION
Installation is in the reverse order of removal.
1. Heating and cooling unit assembly
2. Front blower motor
3. Front blower motor resistor
AWIIA1465ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст