Nissan Note E12. Instruction — part 336
FRONT COIL SPRING AND STRUT
FSU-9
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
REMOVAL AND INSTALLATION
FRONT COIL SPRING AND STRUT
Exploded View
INFOID:0000000009578932
Removal and Installation
INFOID:0000000009578933
REMOVAL
1. Remove the wheel and tire using power tool. Refer to
WT-8, "Removal and Installation"
.
2. Remove brake hose lock plate from strut.
3. Disconnect stabilizer connecting rod from strut. Refer to
.
4. Remove strut bolts and nuts from steering knuckle.
5. Remove stopper insulator lock nut and stopper insulator.
6. Remove strut.
INSTALLATION
Installation is in the reverse order of removal.
• Secure the head of strut piston rod to keep it from rotating, then tighten the stopper insulator lock nut to the
specified torque.
CAUTION:
• Do not reuse stopper insulator lock nut.
• Do not reuse the nuts that secure the strut to the steering knuckle.
• Perform inspection after installation. Refer to
.
• After replacing the strut, always follow the disposal procedure to discard the strut. Refer to
1.
Strut
2.
Coil spring
3.
Bound bumper
4.
Spring upper seat
5.
Strut mount bearing
6.
Piston rod lock nut
7.
Strut mount insulator
8.
Stopper insulator
9.
Stopper insulator lock nut
JPEIA0261GB
WEIA0179E
FSU-10
< REMOVAL AND INSTALLATION >
TRANSVERSE LINK
TRANSVERSE LINK
Exploded View
INFOID:0000000009578934
Removal and Installation
INFOID:0000000009645134
REMOVAL
1. Remove the wheel and tire using power tool. Refer to
WT-8, "Removal and Installation"
.
2. Remove transverse link from steering knuckle. Refer to
.
3. Remove the bolts and nut, then remove the transverse link from front suspension member.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse the transverse link nuts.
Perform the final tightening of the nuts and bolts under unladen conditions with tires on level ground.
Inspection
INFOID:0000000009645135
INSPECTION AFTER REMOVAL
Check the following items and replace the components as necessary.
Transverse link
• Check the transverse link and bushing for deformation, cracks or damage.
• Check the ball joint boot for cracks or other damage, and also for grease leakage.
Swing Torque
1. Move the ball stud at least ten times by hand to check for smooth movement with no binding.
1.
Front suspension member
2.
Transverse link
AWEIA0210GB
TRANSVERSE LINK
FSU-11
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
2. Hook the Tool (A) on the ball joint (B). Confirm the measurement
value is within specifications when the ball stud begins moving.
If swing torque or rotating torque exceeds the specified range,
replace transverse link.
Axial End Play
1. Move the ball stud at least ten times by hand to check for smooth movement with no binding.
2. Move the tip of the ball joint in the axial direction to check for looseness.
If the axial end play exceeds the specified range, replace transverse link.
INSPECTION AFTER INSTALLATION
Check wheel alignment. Refer to
.
Tool number :
—
(J-44372)
Swing torque
: Refer to
.
Rotating torque
: Refer to
.
JPEIA0138ZZ
Axial end play
: Refer to
FSU-12
< REMOVAL AND INSTALLATION >
FRONT STABILIZER
FRONT STABILIZER
Exploded View
INFOID:0000000009578936
Removal and Installation
INFOID:0000000009645136
REMOVAL
1. Remove wheel and tire using power tool. Refer to
WT-8, "Removal and Installation"
.
2. Remove the nuts, then separate the stabilizer connecting rod from the stabilizer bar.
3. Remove the front suspension member. Refer to
FSU-14, "Removal and Installation"
4. Remove the stabilizer clamp bolts, stabilizer clamps and stabi-
lizer bushings from front suspension member.
5. Remove stabilizer bar.
INSTALLATION
Installation is in the reverse order of removal.
1.
Stabilizer bar
2.
Stabilizer clamp
3.
Stabilizer bushing
4.
Stabilizer connecting rod
5.
Strut
6.
Front suspension member
Front
JPEIA0272GB
WEIA0182E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст