Nissan Note E12. Instruction — part 337
FRONT STABILIZER
FSU-13
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
• Install the stabilizer bushing with the slit (A) facing the rear of the
vehicle.
: Rear
• To install stabilizer clamp bolt, temporarily tighten them in numeri-
cal order as shown, then tighten them to the specified torque.
: Front
• To connect the stabilizer connecting rod (1), tighten the nut while
holding the hexagonal part (A) on the stabilizer connecting rod.
• Perform final tightening of bolts and nuts with the vehicle under unladen conditions with tires on level
ground.
• Perform inspection after installation. Refer to
.
Inspection
INFOID:0000000009645137
INSPECTION AFTER REMOVAL
Check the stabilizer bar, the stabilizer connecting rod, the stabilizer bushing, and the stabilizer clamp for defor-
mation, cracks, or damage. Replace components if necessary.
INSPECTION AFTER INSTALLATION
Check the wheel alignment. Refer to
.
JPEIA0273ZZ
JPEIA0274ZZ
JPEIA0252ZZ
FSU-14
< UNIT REMOVAL AND INSTALLATION >
FRONT SUSPENSION MEMBER
UNIT REMOVAL AND INSTALLATION
FRONT SUSPENSION MEMBER
Exploded View
INFOID:0000000009645138
Removal and Installation
INFOID:0000000009645139
REMOVAL
1. Remove the wheel and tire using power tool. Refer to
WT-8, "Removal and Installation"
.
2. Disconnect steering outer sockets from steering knuckles. Refer to
.
3. Disconnect transverse links from steering knuckle. Refer to
4. Disconnect stabilizer connecting rods from stabilizer bar. Refer to
5. Disconnect the lower joint from the steering gear. Refer to
.
6. Set suitable jack under front suspension member.
CAUTION:
Do not damage the front suspension member with suitable jack.
7. Remove the engine rear torque rod. Refer to
.
8. Remove suspension member bolts.
9. Gradually lower the jack to remove front suspension member from vehicle body.
10. If necessary, remove steering gear from front suspension member. Refer to
11. If necessary, remove transverse links. Refer to
.
12. If necessary, remove stabilizer bar, stabilizer bar clamps, and stabilizer bushings. Refer to
13. Inspect the front suspension member. Refer to
INSTALLATION
Installation is in the reverse order of removal.
1.
Front suspension member
2.
Transverse link
AWEIA0210GB
FRONT SUSPENSION MEMBER
FSU-15
< UNIT REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
• Install the member stay bolts, the upper link bolts, and the front
suspension member bolts in the order of 1-6 as shown.
: Front
• After installation, perform the final tightening of each part under unladen conditions with tires on level
ground.
• Complete the inspection.
Inspection
INFOID:0000000009645140
INSPECTION AFTER REMOVAL
Check the front suspension member for cracks, wear or damage. Replace components if necessary.
INSPECTION AFTER INSTALLATION
1. Check the wheel sensor harness to be sure the connectors are fully seated.
2. Check the wheel alignment. Refer to
.
AWEIA0211ZZ
FSU-16
< UNIT DISASSEMBLY AND ASSEMBLY >
FRONT COIL SPRING AND STRUT
UNIT DISASSEMBLY AND ASSEMBLY
FRONT COIL SPRING AND STRUT
Exploded View
INFOID:0000000009578941
Disassembly and Assembly
INFOID:0000000009578942
DISASSEMBLY
CAUTION:
Do not damage strut piston rod when removing components from strut.
1. Remove strut mount insulator.
2. Install Tool (A) to the front coil spring and strut.
CAUTION:
When installing Tool (A), wrap a shop cloth around the front
coil spring and strut to protect the parts from damage.
3. Secure Tool (A) in a vise.
4. Slightly loosen the piston rod lock nut.
WARNING:
Do not remove the piston rod lock nut completely. If the piston rod lock nut is removed com-
pletely, the coil spring can jump out and may cause serious damage or injury.
1.
Strut
2.
Coil spring
3.
Bound bumper
4.
Spring upper seat
5.
Strut mount bearing
6.
Piston rod lock nut
7.
Strut mount insulator
8.
Stopper insulator
9.
Stopper insulator lock nut
JPEIA0261GB
Tool number : ST35652000 ( — )
JPEIA0006ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст