Nissan Note E12. Instruction — part 552
SEC-60
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORK FLOW
Inspect according to Diagnosis Procedure of the system.
Is malfunctioning part detected?
YES
>> GO TO 8.
NO
>> Check intermittent incident.
8.
REPAIR OR REPLACE THE MALFUNCTIONING PART
1. Repair or replace the malfunctioning part.
2. Reconnect parts or connectors disconnected during Diagnosis Procedure again after repair and replace-
ment.
3. Check DTC. If DTC is detected, erase it.
>> GO TO 9.
9.
FINAL CHECK
When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the
malfunction is repaired securely.
When symptom is described by the customer, refer to confirmed symptom in step 3 or 4, and check that the
symptom is not detected.
Is DTC detected and does symptom remain?
YES-1 >> DTC is detected: GO TO 7.
YES-2 >> Symptom remains: GO TO 4.
NO
>> Before returning the vehicle to the customer, always erase DTC.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
SEC-61
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ECM
ECM : Description
INFOID:0000000009016104
Performing the following procedure can automatically activate re-communication of ECM and BCM, but only
when the ECM is replaced with a new one*.
*: New one means an ECM that has never been energized on-board.
(In this step, initialization procedure using CONSULT is not necessary)
NOTE:
• When the replaced ECM is not a brand new, the specified procedure (Initialization and registration)
using CONSULT is necessary.
• If multiple keys are attached to the key holder, separate them before beginning work.
• Distinguish keys with unregistered key IDs from those with registered IDs.
ECM : Work Procedure
INFOID:0000000009016105
1.
PERFORM ECM RE-COMMUNICATING FUNCTION
1. Install ECM.
2. Contact backside of registered Intelligent key* to push-button ignition switch, then turn ignition switch ON.
*: To perform this step, use the key that is used before performing ECM replacement.
3. Maintain ignition switch in the ON position for at least 5 seconds.
4. Turn ignition switch OFF.
5. Start the engine.
>> GO TO 2.
2.
PERFORM ADDITIONAL SERVICE WHEN REPLACING ECM
Refer to
>> Inspection End.
SEC-62
< DTC/CIRCUIT DIAGNOSIS >
P1610 LOCK MODE
DTC/CIRCUIT DIAGNOSIS
P1610 LOCK MODE
Description
INFOID:0000000009567408
ECM forcibly switches to the mode that inhibits engine start, when engine start operation is performed 5 times
or more while communication between ECM and BCM is not normal.
DTC Logic
INFOID:0000000009567409
DTC DETECTION LOGIC
NOTE:
If DTC P1610 is displayed with other DTC (for BCM or ENGINE), first perform the trouble diagnosis for other
DTC.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check DTC in “Self Diagnostic Result” mode of ENGINE using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009567410
1.
CHECK ENGINE START FUNCTION
1. Check that DTC except for DTC P1610 is not detected.
If detected, erase the DTC after fixing.
2. Turn ignition switch OFF.
3. Depress brake pedal and contact the registered Intelligent Key backside to push-button ignition switch,
then wait 5 seconds.
4. Turn ignition switch ON.
5. Turn ignition switch OFF and wait 5 seconds.
6. Repeat steps 3 and 5 twice (a total of 3 times).
7. Check that engine can start.
>> Inspection End.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1610
LOCK MODE
When ECM detects a communication malfunction between
ECM and BCM 5 times or more.
—
P1611 ID DISCORD, IMMU-ECM
SEC-63
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
P1611 ID DISCORD, IMMU-ECM
DTC Logic
INFOID:0000000009567411
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check DTC in Self Diagnostic Result mode of ENGINE using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009567412
1.
PERFORM INITIALIZATION
Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CONSULT
Immobilizer mode and follow the on-screen instructions.
Can the system be initialized and can the engine be started with registered Intelligent Key?
YES
>> Inspection End.
NO
>> GO TO 2.
2.
CHECK SELF DIAGNOSTIC RESULT
1. Select Self Diagnostic Result mode of ENGINE using CONSULT.
2. Erase DTC.
3. Perform DTC CONFIRMATION PROCEDURE for DTC P1611. Refer to
.
Is DTC detected?
YES
>> GO TO 3.
NO
>> Inspection End
3.
REPLACE BCM
1. Replace BCM. Refer to
BCS-67, "Removal and Installation"
.
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-
SULT Immobilizer mode and follow the on-screen instructions.
Can the system be initialized and can the engine be started with registered Intelligent Key?
YES
>> Inspection End.
NO
>> GO TO 4.
4.
REPLACE ECM
1. Replace ECM.
EC-338, "Removal and Installation"
2. Perform “ADDITIONAL SERVICE WHEN REPLACING ECM”.
.
>> Inspection End.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1611
ID DISCORD, IMMU-ECM
The ID verification results between BCM
and ECM are invalid.
• BCM
• ECM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст