Nissan Note E12. Instruction — part 520
RAX-8
< REMOVAL AND INSTALLATION >
REAR WHEEL HUB
3. Remove wheel bearing, using the Tool.
ASSEMBLY
1. Install wheel bearing (1) to brake drum (2), using the Tool (A).
CAUTION:
• Do not reuse wheel bearing.
• Do not apply lubricating oil to the press-fit surface of the
wheel hub bearing.
• Install wheel bearing with the seal rubber part (B) faced to
the brake drum side.
• Set brake drum and wheel bearing horizontally and insert
them vertically.
• The press-fit load must be applied to the wheel bearing
outer race and the brake drum.
• Do not apply press-fit load to the wheel bearing inner race, the seal (B) on the rubber surface
side, and the seal (C) on the metallic surface side. If a press-fit load is applied, the wheel bearing
must be replaced with a new one.
2. Install snap ring to brake drum.
CAUTION:
• Do not damage the wheel bearing seal.
• The snap ring must be installed evenly into the groove.
3. Install sensor rotor, using the Tool (A).
CAUTION:
Do not reuse sensor rotor.
Inspection
INFOID:0000000009499779
INSPECTION AFTER REMOVAL
Check the brake drum and spindle for wear, cracks, and damage. Replace if necessary.
INSPECTION AFTER DISASSEMBLY
• Check brake drum for wear, cracks, or any other damage. Replace if necessary.
• Check snap ring for wear or cracks. Replace if necessary.
INSPECTION AFTER INSTALLATION
1. Check wheel bearing rotating torque per the following instructions.
Tool number : ST33710000 ( — )
JPDIG0079ZZ
Tool number : KV40104730 ( — )
Wheel bearing
press-fit load
: Refer to
Tool number : ST30032000 ( — )
JPDIG0200ZZ
JPDIG0191ZZ
REAR WHEEL HUB
RAX-9
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
NOTE:
The adequacy of turning torque can be judged from a measurement value by a suitable tool.
a. Check the contact surface of the brake drum and spindle for foreign matter. If there is any foreign matter,
clean the contact surface.
b. Check that the wheel hub lock nut is tightened to the specified torque.
c. Turn the brake drum 10 times or more both clockwise and counterclockwise for proper fit.
d. Set a suitable tool to the wheel nut and measure turning torque
at turning speeds of 8 to 12 rpm.
2. Adjust parking brake operation (stroke). Refer to
.
Wheel bearing rotat-
ing torque
: Refer to
.
MDIA0060E
RAX-10
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000009499780
Wheel Hub
INFOID:0000000009499781
Item
Standard
Axial end play
0.0 mm (0.00 in) or less
Rotating torque
1.71 N·m (0.17 kg-m, 15 in-lb) or less
Spring balance measurement
34.2 N (3.49 kg, 7.69 lb) or less
Wheel bearing press-fit load
44.1 - 53.9 kN (4,498.2 - 5,497.8 kg-f, 9,913.7 - 12,116.7 lb-f)
Item
Standard
Wheel stud press-fit load
26.5 - 32.3 kN (2,703.0 - 3,294.6 kg-f, 5,957.2 - 7,261.0 lb-f)
RSU-1
SUSPENSION
C
D
F
G
H
I
J
K
L
M
SECTION
RSU
A
B
RSU
N
O
P
CONTENTS
REAR SUSPENSION
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Suspension . . . . . . . . . ....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tools . . . . . . . . . ....
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
REAR SUSPENSION ASSEMBLY . . . . . .
Inspection . . . . . . . . . . . . . . . . ..
WHEEL ALIGNMENT . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . .
REAR SHOCK ABSORBER . . . . . . . ..
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . . .
Disposal . . . . . . . . . . . . . . . . ...
COIL SPRING . . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
REAR SUSPENSION BEAM . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Wheel Alignment (Unladen*1) . . . . . . . . .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст