Nissan Note E12. Instruction — part 519
RAX-4
< SYMPTOM DIAGNOSIS >
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000009499774
Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×: Applicable
Reference page
—
Possible cause and SUSPECTED PARTS
Im
pro
pe
r in
st
a
lla
tion
, lo
os
en
es
s
Part
s int
erference
Whe
e
l be
ari
ng da
ma
ge
REAR AXLE AND
R
E
AR SUSPENSI
ON
TIRE
ROAD WHEEL
BRAKE
Symptom
Noise
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
Shimmy
×
×
×
×
×
×
Shudder
×
×
×
×
×
Poor quality ride or handling
×
×
×
×
×
REAR WHEEL HUB
RAX-5
< PERIODIC MAINTENANCE >
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
PERIODIC MAINTENANCE
REAR WHEEL HUB
Inspection
INFOID:0000000009499775
• Check the axle and suspension parts for excessive play, wear, or damage.
• Shake each rear wheel to check for excessive play as shown.
REAR WHEEL BEARING INSPECTION
• Move wheel in the axial direction by hand. Make sure the axial end play is within specification.
• Check that the wheel bearing operates smoothly.
• Replace the wheel bearing if the axial end play exceeds specification, or if the wheel bearing does not turn
smoothly. Refer to
RAX-6, "Removal and Installation"
.
CAUTION:
The wheel bearing does not require maintenance. If any of the following symptoms are noted,
replace the wheel bearing.
• Growling noise is emitted from the wheel bearing during operation.
• Wheel bearing drags or turns roughly.
SMA525A
Axial end play
: Refer to
RAX-6
< REMOVAL AND INSTALLATION >
REAR WHEEL HUB
REMOVAL AND INSTALLATION
REAR WHEEL HUB
Exploded View
INFOID:0000000009499776
Removal and Installation
INFOID:0000000009499777
REMOVAL
1. Remove the wheel and tire using power tool. Refer to
WT-8, "Removal and Installation"
.
2. Remove hub cap from brake drum using a suitable tool.
3. Remove wheel hub lock nut and brake drum.
CAUTION:
• Do not depress brake pedal while rear drum is removed.
• Do not apply force to the brake drum to avoid damage to the wheel bearing. If the wheel bearing
inner race is separated due to force, replace the wheel bearing with a new one.
4. Remove spindle bolts. Separate back plate and spindle from rear suspension beam.
CAUTION:
Do not remove rear brake components. Support the rear brake components using wire.
5. If required, remove the wheel studs from brake drum using a suitable press.
CAUTION:
• Do not hammer the wheel stud and avoid impact to the brake drum.
• Press the wheel stud straight out to avoid damage.
INSTALLATION
Installation is in the reverse order of removal.
1.
Rear suspension beam
2.
Rear brake components
3.
Spindle
4.
Sensor rotor
5.
Snap ring
6.
Wheel bearing
7.
Wheel stud
8.
Brake drum
9.
Wheel hub lock nut
10. Hub cap
AWDIA1107ZZ
REAR WHEEL HUB
RAX-7
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
If required, position the wheel stud (1) to the brake drum. Place
Position the stud (1) to the brake drum. Place a washer (A) on the
opposite end of the stud and by use of a nut (B), tighten to press the
stud into the brake drum.
CAUTION:
• Check that no clearance exists between brake drum, and the
wheel stud after installation.
• Do not reuse wheel stud.
Insert brake drum in a straight line onto the spindle.
CAUTION:
• If the brake drum becomes stuck and must be pulled out, do not use tools. Replace the wheel bear-
ing with a new one if the brake drum cannot be pulled out without use of tools.
• If the brake drum becomes stuck and the wheel bearing inner race is damaged, replace the wheel
bearing with a new one.
• Do not damage the wheel bearing seal. If damaged, replace wheel bearing with new one.
Using the Tool, install hub cap on brake drum as shown.
CAUTION:
• Do not reuse hub cap.
• Do not reuse wheel hub lock nut.
• Tighten the wheel hub lock nut to the specified torque. Refer
.
Disassembly and Assembly
INFOID:0000000009499778
DISASSEMBLY
1. Remove sensor rotor, using a suitable tool (A).
CAUTION:
Do not damage the brake drum.
2. Remove snap ring (1).
Wheel stud press-fit load
: Refer to
JPDIF0300ZZ
Tool number : ST30720000 ( — )
SDIA0766J
JPDIG0097ZZ
JPDIG0092ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст