Nissan Note E12. Instruction — part 505
PWC-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
D
E
F
G
H
I
J
L
M
SECTION
PWC
A
B
PWC
N
O
P
CONTENTS
POWER WINDOW CONTROL SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Work . . . . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
Component Parts Location . . . . . . . . . ....
Power Window Main Switch . . . . . . . . . ..
Power Window Switch . . . . . . . . . . . ...
Power Window Motor . . . . . . . . . . . ....
SYSTEM . . . . . . . . . . . . . . . ..
System Diagram . . . . . . . . . . . . . ....
System Description . . . . . . . . . . . . ...
DIAGNOSIS SYSTEM (BCM) . . . . . . . .
COMMON ITEM . . . . . . . . . . . . . . ...
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . ...
RETAINED PWR . . . . . . . . . . . . . .....
RETAINED PWR : CONSULT Function (BCM -
RETAINED PWR) . . . . . . . . . . . . .....
ECU DIAGNOSIS INFORMATION . . . ..
BCM . . . . . . . . . . . . . . . . .
List of ECU Reference . . . . . . . . . . .
POWER WINDOW MAIN SWITCH . . . . .
Reference Value . . . . . . . . . . . . . .
WIRING DIAGRAM . . . . . . . . . ..
POWER WINDOW SYSTEM . . . . . . . .
Wiring Diagram . . . . . . . . . . . . . .
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORK FLOW . ...
Work Flow . . . . . . . . . . . . . . . .
DTC/CIRCUIT DIAGNOSIS . . . . . . .
POWER SUPPLY AND GROUND CIRCUIT .
BODY CONTROL SYSTEM . . . . . . . . . ...
BODY CONTROL SYSTEM : Diagnosis Proce-
dure . . . . . . . . . . . . . . . . . . .
POWER WINDOW MAIN SWITCH . . . . . . .
POWER WINDOW MAIN SWITCH : Diagnosis
Procedure . . . . . . . . . . . . . . . .
FRONT POWER WINDOW SWITCH (PASSEN-
GER SIDE) . . . . . . . . . . . . . . . . .
FRONT POWER WINDOW SWITCH (PASSEN-
GER SIDE) : Diagnosis Procedure . . . . . . ..
REAR POWER WINDOW SWITCH . . . . . . ...
REAR POWER WINDOW SWITCH : Diagnosis
Procedure . . . . . . . . . . . . . . . .
FRONT POWER WINDOW SWITCH (PAS-
SENGER SIDE) . . . . . . . . . . . . .
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
Component Inspection . . . . . . . . . . . .
REAR POWER WINDOW SWITCH . . . . ..
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
PWC-2
DRIVER SIDE . . . . . . . . . . . . . . ....
DRIVER SIDE : Component Function Check . . .
DRIVER SIDE : Diagnosis Procedure . . . . ....
PASSENGER SIDE . . . . . . . . . . . . ...
PASSENGER SIDE : Component Function Check
...
PASSENGER SIDE : Diagnosis Procedure . . ...
REAR LH . . . . . . . . . . . . . . . . ...
REAR LH : Component Function Check . . . ....
REAR LH : Diagnosis Procedure . . . . . . ....
REAR RH . . . . . . . . . . . . . . . . ..
REAR RH : Component Function Check . . . ....
REAR RH : Diagnosis Procedure . . . . . . ...
SYMPTOM DIAGNOSIS . . . . . . . .
POWER WINDOWS DO NOT OPERATE
WITH POWER WINDOW MAIN SWITCH . . .
Diagnosis Procedure . . . . . . . . . . . ..
DRIVER SIDE POWER WINDOW DOES NOT
OPERATE . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ..
FRONT PASSENGER SIDE POWER WIN-
DOW DOES NOT OPERATE . . . . . . .
WHEN FRONT POWER WINDOW SWITCH (PAS-
SENGER SIDE) IS OPERATED . . . . . . . ....
WHEN POWER WINDOW MAIN SWITCH IS OP-
ERATED . . . . . . . . . . . . . . . . ....
WHEN POWER WINDOW MAIN SWITCH IS OP-
ERATED : Diagnosis Procedure . . . . . . . .
REAR LH SIDE POWER WINDOW DOES
NOT OPERATE . . . . . . . . . . . . .
WHEN REAR POWER WINDOW SWITCH LH IS
OPERATED . . . . . . . . . . . . . . . ...
WHEN REAR POWER WINDOW SWITCH LH IS
OPERATED : Diagnosis Procedure . . . . . .
WHEN POWER WINDOW MAIN SWITCH IS OP-
ERATED . . . . . . . . . . . . . . . . .
WHEN POWER WINDOW MAIN SWITCH IS OP-
ERATED : Diagnosis Procedure . . . . . . . .
REAR RH SIDE POWER WINDOW DOES
NOT OPERATE . . . . . . . . . . . . .
WHEN REAR POWER WINDOW SWITCH RH IS
OPERATED . . . . . . . . . . . . . . . ...
WHEN REAR POWER WINDOW SWITCH RH IS
OPERATED : Diagnosis Procedure . . . . . .
WHEN POWER WINDOW MAIN SWITCH IS OP-
ERATED . . . . . . . . . . . . . . . . .
WHEN POWER WINDOW MAIN SWITCH IS OP-
ERATED : Diagnosis Procedure . . . . . . . .
POWER WINDOW RETAINED POWER OP-
ERATION DOES NOT OPERATE PROPERLY
...
Diagnosis Procedure . . . . . . . . . . . ...
POWER WINDOW LOCK SWITCH DOES
NOT FUNCTION . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . ..
MAIN POWER WINDOW AND DOOR LOCK/
UNLOCK SWITCH . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
POWER WINDOW AND DOOR LOCK/UN-
LOCK SWITCH RH . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
REAR POWER WINDOW SWITCH . . . . ..
PRECAUTIONS
PWC-3
< PRECAUTION >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009567634
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Instruction.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Work
INFOID:0000000009567635
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
PWC-4
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009567636
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-46534)
Trim Tool Set
Removing trim components
AWJIA0483ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст