Nissan Note E12. Instruction — part 384
INL-1
DRIVER CONTROLS
C
D
E
F
G
H
I
J
K
M
SECTION
INL
A
B
INL
N
O
P
CONTENTS
INTERIOR LIGHTING SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Work . . . . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
Component Parts Location . . . . . . . . . ....
SYSTEM . . . . . . . . . . . . . . . ..
INTERIOR ROOM LAMP CONTROL SYSTEM . . ..
INTERIOR ROOM LAMP CONTROL SYSTEM :
System Description . . . . . . . . . . . . ...
ILLUMINATION CONTROL SYSTEM . . . . . .....
ILLUMINATION CONTROL SYSTEM : System
Description . . . . . . . . . . . . . . . ....
DIAGNOSIS SYSTEM (BCM) . . . . . . . .
COMMON ITEM . . . . . . . . . . . . . . ...
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . ...
INT LAMP . . . . . . . . . . . . . . . . ....
INT LAMP : CONSULT Function (BCM - INT
LAMP) . . . . . . . . . . . . . . . . . .
BATTERY SAVER . . . . . . . . . . . . . .
BATTERY SAVER : CONSULT Function (BCM -
BATTERY SAVER) . . . . . . . . . . . . .
ECU DIAGNOSIS INFORMATION . . . ..
BCM . . . . . . . . . . . . . . . . ...
List of ECU Reference . . . . . . . . . . . .
WIRING DIAGRAM . . . . . . . . . ..
INTERIOR ROOM LAMP CONTROL SYSTEM
...
Wiring Diagram . . . . . . . . . . . . . .
ILLUMINATION . . . . . . . . . . . . .
Wiring Diagram . . . . . . . . . . . . . .
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORKFLOW . .
Work Flow . . . . . . . . . . . . . . . .
DTC/CIRCUIT DIAGNOSIS . . . . . . .
POWER SUPPLY AND GROUND CIRCUIT .
BODY CONTROL SYSTEM . . . . . . . . . ...
BODY CONTROL SYSTEM : Diagnosis Proce-
dure . . . . . . . . . . . . . . . . . . .
BATTERY SAVER OUTPUT/POWER SUP-
PLY CIRCUIT . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . ...
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
INTERIOR ROOM LAMP CONTROL CIRCUIT
...
Description . . . . . . . . . . . . . . . ...
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
CARGO LAMP CONTROL CIRCUIT . . . .
Description . . . . . . . . . . . . . . . ...
Component Function Check . . . . . . . . .
INL-2
PUSH-BUTTON IGNITION SWITCH ILLUMI-
NATION CIRCUIT . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ..
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . . .
INTERIOR LIGHTING SYSTEM SYMPTOMS ...
Symptom Table . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . ...
MAP LAMP . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . ....
Bulb Replacement . . . . . . . . . . . . ..
INTERIOR ROOM LAMP . . . . . . . . ...
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . . .
Bulb Replacement . . . . . . . . . . . . ...
CARGO ROOM LAMP . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Bulb Replacement . . . . . . . . . . . . ...
SHIFT SELECTOR LAMP . . . . . . . . .
Bulb Replacement . . . . . . . . . . . . ...
ILLUMINATION CONTROL SWITCH . . . ...
Removal and Installation . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
PRECAUTIONS
INL-3
< PRECAUTION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009541368
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Instruction.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Work
INFOID:0000000009445821
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
INL-4
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009445822
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-46534)
Trim Tool Set
Removing trim components
AWJIA0483ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст