Nissan Note E12. Instruction — part 631
TM-82
< SYSTEM DESCRIPTION >
[CVT: RE0F11A]
SYSTEM
SHIFT CONTROL : System Description
INFOID:0000000009019864
SYSTEM DIAGRAM
DESCRIPTION
To select the gear ratio that can give the driving force to meet driver's intent or vehicle situation, the vehicle
driving condition such as vehicle speed or accelerator pedal position is detected and the most appropriate
gear ratio is selected and the shifting method before reaching the speed is determined. The information is
output to the primary pressure solenoid valve to control the line pressure input/output to the primary pulley, to
determine the primary pulley (movable pulley) position and to control the gear position.
D Position (Normal)
JSDIA2632GB
SYSTEM
TM-83
< SYSTEM DESCRIPTION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Gear shifting is performed in all shifting ranges from the lowest to the
highest gear ratio.
D Position (OD OFF)
The gear ratio is generally high by limiting the shifting range on the
high side, and this always generates a large driving power.
L Position
By limiting the shifting range only to the lowest of the gear ratio, a
large driving force and engine brake are obtained.
Hill Climbing And Descending Control
If a downhill is detected with the accelerator pedal is released, the system performs downshift to increase the
engine brake force so that vehicle may not be accelerated more than necessary. If a climbing hill is detected,
the system improves the acceleration performance in re-acceleration by limiting the gear shift range on the
high side.
NOTE:
For engine brake control on a downhill, the control can be stopped with CONSULT.
Control In Acceleration
From change of the vehicle speed or accelerator pedal position, the acceleration request level of the driver or
driving scene is evaluated. In start or acceleration during driving, the gear shift characteristics with linearity of
revolution increase and vehicle speed increase are gained to improve the acceleration feel.
SELECT CONTROL
SCIA1953E
SCIA8229E
SCIA8240E
JSDIA2060GB
TM-84
< SYSTEM DESCRIPTION >
[CVT: RE0F11A]
SYSTEM
SELECT CONTROL : System Description
INFOID:0000000009019865
SYSTEM DIAGRAM
DESCRIPTION
Based on accelerator pedal angle, engine speed, primary pulley speed, and the secondary pulley speed, the
optimum operating pressure is set to reduce impact of a selector lever operation while shifting from “N” (“P”) to
“D” (“R”) position.
LOCK-UP CONTROL
JSDIA1862GB
SYSTEM
TM-85
< SYSTEM DESCRIPTION >
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
LOCK-UP CONTROL : System Description
INFOID:0000000009019866
SYSTEM DIAGRAM
DESCRIPTION
• Controls for improvement of the transmission efficiency by engaging the torque converter clutch in the
torque converter and eliminating slip of the converter. Achieves comfortable driving with slip control of the
torque converter clutch.
• The oil pressure feed circuit for the torque converter clutch piston chamber is connected to the torque con-
verter clutch control valve. The torque converter clutch control valve is switched by the torque converter
clutch solenoid valve with the signal from TCM. This controls the oil pressure circuit, which is supplied to the
torque converter clutch piston chamber, to the release side or engagement side.
• If the CVT fluid temperature is low or the vehicle is in fail-safe mode due to malfunction, lock-up control is
prohibited.
Lock-up engagement
In lock-up engagement, the torque converter clutch solenoid valve makes the torque converter clutch control
valve locked up to generate the lock-up apply pressure. This pushes the torque converter clutch piston for
engagement.
Lock-up release condition
In lock-up release, the torque converter clutch solenoid valve makes the torque converter clutch control valve
non-locked up to drain the lock-up apply pressure. This does not engage the torque converter clutch piston.
IDLE NEUTRAL CONTROL
JSDIA1865GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст