Nissan Note E12. Instruction — part 304
EXL-84
< DTC/CIRCUIT DIAGNOSIS >
TAIL LAMP CIRCUIT
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace IPDM E/R.
5.
CHECK TAIL LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and rear combination lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK TAIL LAMP GROUND OPEN CIRCUIT
Check continuity between rear combination lamp harness connector and ground.
Is the inspection result normal?
YES
>> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO
>> Repair or replace harness.
(+)
(
−)
Test item
Voltage
(Approx.)
IPDM E/R
Connector
Terminal
E45
23
Ground
EXTERNAL
LAMPS
TAIL
Battery voltage
Off
0 V
IPDM E/R
Rear combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E45
23
B27
1
Yes
LH
B25
Rear combination lamp
Ground
Continuity
Connector
Terminal
RH
B27
6
Yes
LH
B25
LICENSE PLATE LAMP CIRCUIT
EXL-85
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LICENSE PLATE LAMP CIRCUIT
Component Function Check
INFOID:0000000009472898
1.
CHECK TAIL LAMP OPERATION
Check that the tail lamp is turned ON.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check tail lamp circuit. Refer to
EXL-83, "Component Function Check"
.
2.
CHECK LICENSE PLATE LAMP OPERATION
CONSULT ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the lighting switch, check that the license plate lamp is turned ON.
Is the inspection result normal?
YES
>> License plate lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009472899
1.
CHECK LICENSE PLATE LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace bulb.
2.
CHECK LICENSE PLATE LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector and license plate lamp connector.
3. Check continuity between IPDM E/R harness connector and license plate lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK LICENSE PLATE LAMP GROUND OPEN CIRCUIT
Check continuity between license plate lamp harness connector and ground.
Is the inspection result normal?
YES
>> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO
>> Repair or replace harness.
TAIL
: License plate lamp ON
Off
: License plate lamp OFF
IPDM E/R
License plate lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E45
23
D508
1
Yes
LH
D507
License plate lamp
Ground
Continuity
Connector
Terminal
RH
D508
2
Yes
LH
D507
EXL-86
< DTC/CIRCUIT DIAGNOSIS >
TURN SIGNAL LAMP CIRCUIT
TURN SIGNAL LAMP CIRCUIT
Component Function Check
INFOID:0000000009472900
1.
CHECK TURN SIGNAL LAMP
CONSULT ACTIVE TEST
1. Select “FLASHER” of BCM (FLASHER) active test item.
2. With operating the test items, check that the turn signal lamps is turned ON.
Is the inspection result normal?
YES
>> Turn signal lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009472901
1.
CHECK TURN SIGNAL LAMP
CONSULT ACTIVE TEST
1. Select “FLASHER” of BCM (FLASHER) active test item.
2. With operating the test items, check that the turn signal lamps is turned ON.
Which turn signal lamp does not turn ON?
Side turn signal lamp>>GO TO 3.
Other than side turn signal lamp>>GO TO 2.
2.
CHECK TURN SIGNAL LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace bulb.
3.
CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE
1. Turn ignition switch OFF.
2. Disconnect front combination lamp connector, side turn signal lamp connector and rear combination lamp
connector.
3. Turn ignition switch ON.
4. With operating the turn signal switch, check voltage between BCM harness connector and ground.
LH
: Turn signal lamps (LH) ON
RH
: Turn signal lamps (RH) ON
Off
: Turn signal lamps OFF
LH
: Turn signal lamps (LH) ON
RH
: Turn signal lamps (RH) ON
Off
: Turn signal lamps OFF
TURN SIGNAL LAMP CIRCUIT
EXL-87
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 5.
4.
CHECK TURN SIGNAL LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM harness connector and front combination lamp, door mirror or rear combi-
nation lamp harness connector.
Front turn signal lamp
Rear turn signal lamp
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
5.
CHECK TURN SIGNAL LAMP SHORT CIRCUIT
Check continuity between BCM harness connector and ground.
(+)
(–)
Condition
Voltage
(Approx.)
BCM
Connector
Terminal
LH
M99
60
Ground
Turn signal
switch
LH
OFF
0 V
RH
61
RH
OFF
0 V
PKID0926E
PKID0926E
BCM
Front combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
M99
61
E30 (Without DTRL)
4
Yes
LH
60
E29 (Without DTRL)
RH
61
E76 (With DTRL)
LH
60
E75 (With DTRL)
BCM
Rear combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
M99
61
B27
4
Yes
LH
60
B25
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст