Nissan Xterra. Instruction — part 217
DLK-110
< REMOVAL AND INSTALLATION >
DOOR
Installation
Installation is in the reverse order of removal.
• Align the front door. Refer to
.
REAR DOOR
Removal
1. Remove the door finisher. Refer to
INT-14, "Removal and Installation"
.
2. Remove the inner seal.
3. Remove the rear door glass and regulator. Refer to
GW-18, "Rear Door Glass Regulator"
.
4. Remove the door harness.
5. Remove the check link bolt from the hinge pillar.
6. Remove the door-side hinge nuts, and remove the door assembly.
Installation
Installation is in the reverse order of removal.
• Align the rear door. Refer to
Door hinge nuts
25.8 N·m (2.6 kg-m, 19 ft-lb)
LIIA1727E
Check link to hinge pillar
bolt
14.7 N·m (1.5 kg-m, 11 ft-lb)
LIIA1726E
Door hinge nuts
25.8 N·m (2.6 kg-m, 19 ft-lb)
LIIA1727E
DOOR
DLK-111
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR
Removal
1. Remove the glass hatch.
2. Remove the back door lock assembly. Refer to
DLK-116, "Component Structure"
3. Remove the back door wire harness.
4. Remove the rear washer nozzle and hose from the back door. Refer to
5. Support the back door.
6. Remove the back door stays.
7. Remove the door side nuts and the back door assembly.
CAUTION:
Two technicians should be used to avoid damaging the back door during removal.
Installation
Installation is in the reverse order of removal.
• Align the back door. Refer to
Back Door Stay Disposal
INFOID:0000000009485095
1. Fix back door stay (1) using a vise (C).
2. Using hacksaw (A) slowly make 2 holes in the back door stay, in
numerical order as shown.
CAUTION:
• When cutting a hole on back door stay, always cover a
hacksaw using a shop cloth (B) to avoid scattering metal
fragments or oil.
• Wear eye protection (safety glasses).
• Wear gloves.
WIIA1056E
JMKIA3336ZZ
A: 20 mm (0.787 in)
B: Cut at the groove.
JMKIA3609ZZ
DLK-112
< REMOVAL AND INSTALLATION >
FRONT DOOR LOCK
FRONT DOOR LOCK
Component Structure
INFOID:0000000009485096
Removal and Installation
INFOID:0000000009485097
REMOVAL
1. Remove the front door finisher. Refer to
INT-14, "Removal and Installation"
2. Remove the front door glass rear run channel.
3. Remove door side grommet and door key cylinder assembly
(driver side) or door outside handle escutcheon (passenger
side) bolts from grommet hole.
(1): Weatherstrip
(2): Bolt
1.
Grommet
2.
Front door striker
3.
Door lock assembly
4.
Door outside handle cable
5.
Inside handle assembly
6.
Inside handle cable
7.
Door lock cable
8.
Key cylinder rod (Driver side only)
9.
Door key cylinder
10. Door outside handle bracket
11. Front gasket
12. Door outside handle
13. Door key cylinder assembly (Driver
side) door outside handle escutch-
eon (Passenger side)
14. Rear gasket
Front
AWKIA1793GB
AWKIA2017ZZ
FRONT DOOR LOCK
DLK-113
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
4. While pulling the door outside handle (1), remove door key cylin-
der assembly or escutcheon (2).
5. Separate the door key cylinder rod from the door key cylinder assembly (if equipped).
6. While pulling door outside handle (1), slide toward rear of vehi-
cle to remove door outside handle.
7. Remove the front gasket (1) and rear gasket (2).
8. Remove the bolts and the door lock assembly.
CAUTION:
Do not reuse bolts.
ALKIA0956ZZ
JMKIA0524ZZ
ALKIA0924ZZ
AWKIA2018ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст