Nissan Xterra. Instruction — part 448
GW-14
< UNIT REMOVAL AND INSTALLATION >
FRONT DOOR GLASS AND REGULATOR
FRONT DOOR GLASS AND REGULATOR
Front Door Glass
INFOID:0000000009484312
REMOVAL
1. Remove the front door finisher. Refer to
INT-14, "Removal and Installation"
2. Remove the rear bracket and the vapor barrier.
3. Remove the window inside seals covering the glass bolts.
4. Temporarily reconnect the power window switch.
5. Operate the power window switch to raise/lower the door win-
dow until the glass bolts can be seen.
6. Remove the glass bolts.
7. While holding the door window, raise it at the rear and pull the
glass out of the sash toward the outside of the door.
INSTALLATION
Installation is in the reverse order of removal.
• Check the glass for proper fit. Follow the FITTING INSPECTION procedure.
• On the driver door, perform system initialization. Refer to
PWC-61, "Removal and Installation"
FITTING INSPECTION
• Check that the glass is securely fit into the glass run groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.39 to 0.79 in)] and check that the clearance to the
sash is parallel. If the clearance between the glass and sash is not parallel, loosen the regulator bolts, guide
rail bolts, and glass and guide rail bolts to correct the glass position.
Front Door Glass Regulator
INFOID:0000000009484313
REMOVAL
1. Remove the front door finisher. Refer to
INT-14, "Removal and Installation"
2. Partially remove the vapor barrier and position aside.
3. Remove the inside window seals covering the glass bolts.
4. Temporarily reconnect the power window switch.
LIIA1686E
LIIA1687E
Glass bolts
: 6.1 N·m (0.62 kg-m, 54 in-lb)
FRONT DOOR GLASS AND REGULATOR
GW-15
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
5. Operate the power window switch to raise/lower the door win-
dow until the glass bolts can be seen.
6. Remove the glass bolts.
7. Raise the front door glass and hold it in place with suitable tool
(A).
8. Disconnect the harness connector from the regulator assembly.
9. Remove the bolts and the regulator assembly.
DISASSEMBLY AND ASSEMBLY
Remove the regulator motor from the regulator assembly.
INSPECTION AFTER REMOVAL
LIIA1686E
PIIB3510J
Front
WIIA1033E
GW-16
< UNIT REMOVAL AND INSTALLATION >
FRONT DOOR GLASS AND REGULATOR
Check the regulator assembly for the following items. If a malfunction is detected, replace or grease it.
• Wire wear
• Regulator deformation
• Grease condition for each sliding part
INSTALLATION
1. Install the regulator assembly.
a. Loosely install the top rear regulator bolt to use along with the temporary holds on the window motor to
install the assembly in the door.
b. Install the top front regulator bolt.
c.
Install the bottom front regulator bolt.
d. Install the bottom rear regulator bolt.
e. Tighten the top rear regulator bolt.
f.
Install the top window motor bolt.
g. Install the lower window motor bolt
h. Install the rear window motor bolt.
2. Connect the harness connector to the regulator assembly.
Front
Regulator and motor bolts : 5.1 N·m (0.52 kg-m, 45 in-lb)
WIIA1033E
FRONT DOOR GLASS AND REGULATOR
GW-17
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
3. Lower the glass and ensure that it is in both the front and rear
glass channels. Tighten glass bolts.
4. Check the glass for proper fit.
5. Install the window inside seals over the glass bolt holes.
6. Install the vapor barrier.
7. Install front door finisher. Refer to
INT-14, "Removal and Installation"
.
8. On the driver door, perform system initialization. Refer to
PWC-61, "Removal and Installation"
Glass mounting bolts : 6.1 N·m (0.62 kg-m, 54 in-lb)
LIIA1686E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст