Nissan Xterra. Instruction — part 449
GW-18
< UNIT REMOVAL AND INSTALLATION >
REAR DOOR GLASS AND REGULATOR
REAR DOOR GLASS AND REGULATOR
Rear Door Glass
INFOID:0000000009484314
REMOVAL
1. Remove the rear door finisher. Refer to
INT-14, "Removal and Installation"
.
2. Remove the rear door handle bracket.
3. Remove the vapor barrier.
4. Temporarily reconnect the power window switch.
5. Remove the glass run from the partition glass.
6. Operate the power window switch to raise/lower the door win-
dow until the glass bolts can be seen.
7. Remove the partition sash bolt (lower) and screw (upper) to
remove the sash.
8. Remove the bolts and the glass.
INSTALLATION
Installation is in the reverse order of removal.
• Check the glass alignment. Follow the FITTING INSPECTION procedure.
FITTING INSPECTION
• Check that the glass is securely fit into the glass run groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.39 to 0.79 in)], and check that the clearance to the
sash is parallel. If the clearance between the glass and sash is not parallel, loosen the regulator bolts, guide
rail bolts, and glass carrier plate bolts to correct the glass position.
Rear Door Glass Regulator
INFOID:0000000009484315
REMOVAL
1. Remove the rear door finisher. Refer to
INT-14, "Removal and Installation"
.
2. Remove the rear door handle bracket.
3. Position the vapor barrier aside.
4. Temporarily reconnect the power window switch.
5. Operate the power window switch to raise/lower the door win-
dow until the glass bolts can be seen.
LIIA1689E
Glass bolts : 6.1 N·m (0.62 kg-m, 54 in-lb)
LIIA1689E
REAR DOOR GLASS AND REGULATOR
GW-19
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
6. Raise the rear door glass and hold it in place with suitable tool
(A).
7. Remove the bolts and the regulator assembly.
• Disconnect the harness connector from the regulator assembly.
INSPECTION AFTER REMOVAL
Check the regulator assembly for the following items. If a malfunction is detected, replace or grease it.
• Gear wear
• Regulator deformation
• Spring damage
• Grease condition for each sliding part
INSTALLATION
PIIB3511J
Front
WIIA1034E
GW-20
< UNIT REMOVAL AND INSTALLATION >
REAR DOOR GLASS AND REGULATOR
1. Connect the harness connector and install the regulator assembly.
a. Loosely install the top rear regulator bolt to use along with the temporary holds on the window motor to
install the assembly in the door.
b. Install the top front regulator bolt.
c.
Install the bottom regulator bolt.
d. Tighten the top rear regulator bolt.
e. Install the top window motor bolt.
f.
Install the lower window motor bolt.
g. Install the front window motor bolt.
2. Lower the glass and ensure that it is in both the front and rear
glass channels. Tighten the bolts.
3. Install the partition sash.
4. Check the glass alignment.
5. Install the rear door handle bracket.
6. Reposition the vapor barrier.
7. Install the rear door finisher. Refer to
INT-14, "Removal and Installation"
Front
Regulator assembly
: 7.5 N·m (0.77 kg-m, 66 in-lb)
Glass bolts
: 6.1 N·m (0.62 kg-m, 54 in-lb)
WIIA1034E
LIIA1689E
SIDE WINDOW GLASS
GW-21
< UNIT REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
SIDE WINDOW GLASS
Removal and Installation
INFOID:0000000009484316
1.
Glass
2.
Primer area
3.
Body side outer
4.
Rear door assembly
5.
Back door assembly
6.
Locating clips
7.
Urethane
a.
15 mm (0.59 in)
b.
42.5 mm (1.67 in)
WIIA1035E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст