Nissan Frontier. Instruction — part 308
DLN-134
< UNIT REMOVAL AND INSTALLATION >
[PROPELLER SHAFT: 2F1310]
PROPELLER SHAFT
UNIT REMOVAL AND INSTALLATION
PROPELLER SHAFT
Removal and Installation
INFOID:0000000009479729
COMPONENTS
Model 2F1310
REMOVAL
1. Remove under cover (if equipped). Refer to
EXT-15, "Removal and Installation"
.
2. Put matching marks on the front propeller shaft flange yoke and
the front final drive companion flange as shown.
CAUTION:
For matching marks, use paint. Do not damage the flange
yoke and companion flange of the front final drive.
3. Put matching marks on the front propeller shaft flange yoke and
the transfer companion flange.
CAUTION:
For matching marks, use paint. Do not damage the flange
yoke and companion flange of the front final drive.
4. Remove the bolts and then remove the front propeller shaft from
the front final drive and transfer.
INSPECTION
WDIA0304E
1.
Propeller shaft tube
2.
Snap ring
3.
Journal bearing
4.
Journal
5.
Flange yoke
Front
SDIA2046E
PROPELLER SHAFT
DLN-135
< UNIT REMOVAL AND INSTALLATION >
[PROPELLER SHAFT: 2F1310]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• Inspect the propeller shaft runout. If runout exceeds the limit,
replace the propeller shaft assembly. Refer to
• While holding the flange yoke on one side, check axial play of the
joint as shown. If the journal axial play exceeds the specification,
repair or replace the journal parts. Refer to
• Check the propeller shaft tube surface for dents or cracks. If dam-
age is detected, replace the propeller shaft assembly.
INSTALLATION
Installation is in the reverse order of removal.
• After installation, check for vibration by driving the vehicle. Refer to
DLN-132, "NVH Troubleshooting Chart"
.
CAUTION:
Do not reuse the bolts and nuts. Always install new ones.
LDIA0118E
LDIA0117E
DLN-136
< UNIT DISASSEMBLY AND ASSEMBLY >
[PROPELLER SHAFT: 2F1310]
PROPELLER SHAFT
UNIT DISASSEMBLY AND ASSEMBLY
PROPELLER SHAFT
Disassembly and Assembly
INFOID:0000000009479730
DISASSEMBLY
Journal
1. Put matching marks on the front propeller shaft and flange yoke
as shown.
CAUTION:
For matching marks, use paint. Do not damage the front
propeller shaft or flange yoke.
2. Remove the snap rings.
CAUTION:
Do not reuse snap rings.
3. Push out and remove the journal bearings by lightly tapping the
flange yoke with a hammer, taking care not to damage the jour-
nal or flange yoke hole.
NOTE:
Put marks on the disassembled parts so that they can be rein-
stalled in their original positions from which they were removed.
4. Push out and remove the remaining journal bearings at the
opposite side by lightly tapping the flange yoke with a hammer,
taking care not to damage the journal or flange yoke hole.
NOTE:
Put marks on the disassembled parts so that they can be rein-
stalled in their original positions from which they were removed.
ASSEMBLY
SPD128
APD011
SPD732
SPD131
PROPELLER SHAFT
DLN-137
< UNIT DISASSEMBLY AND ASSEMBLY >
[PROPELLER SHAFT: 2F1310]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Journal
1. Assemble the journal bearings. Apply multipurpose grease on
the bearing inner surface.
NOTE:
During assembly, use caution so that the needle bearings do not
fall down.
2. Select new snap rings that will provide the specified play in an
axial direction of the journal, and install them. Refer to
.
CAUTION:
Do not reuse snap rings
NOTE:
Select snap rings with a difference in thickness at both sides
within 0.02 mm (0.0008 in).
3. Adjust the thrust clearance between the bearing and snap ring
to zero by tapping the yoke.
4. Make sure that the journal moves smoothly and is below the
joint flex effort specification. Refer to
.
WPD019
APD012
SPD732
LDIA0119E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст