Nissan Frontier. Instruction — part 1271
CONTROL VALVE WITH TCM
TM-295
< REMOVAL AND INSTALLATION >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
15. Install snap ring to A/T assembly harness connector.
16. Connect A/T assembly harness connector.
17. Connect the negative battery terminal.
18. Refill the A/T with fluid and check the fluid level and for fluid
leakage. Refer to
TM-269, "Checking the A/T Fluid (ATF)"
SCIA5039E
TM-296
< REMOVAL AND INSTALLATION >
[5AT: RE5R05A]
REAR OIL SEAL
REAR OIL SEAL
Removal and Installation
INFOID:0000000009480682
REMOVAL
1. Remove rear propeller shaft. Refer to
DLN-143, "Removal and Installation"
DLN-163, "Removal and Installation"
(3S1330-2BJ100).
2. Remove transfer from transmission (4WD models). Refer to
DLN-101, "Removal and Installation"
(TX15B).
3. Remove rear oil seal using a suitable tool.
CAUTION:
Do not scratch rear extension assembly (2WD models) or
adapter case assembly (4WD models).
INSTALLATION
1. Install new rear oil seal until it is flush into the rear extension
case (2WD models) using Tool or adapter case (4WD models)
using suitable tool.
CAUTION:
• Apply ATF to rear oil seal.
• Do not reuse rear oil seal.
2. Install transfer to transmission (4WD models). Refer to
101, "Removal and Installation"
3. Install rear propeller shaft. Refer to
(2S1330),
DLN-152, "Removal and Installation"
(3S1310),
DLN-163, "Removal and Installation"
(3S1330),
174, "Removal and Installation"
4. Check the A/T fluid level and for fluid leaks. Refer to
"Checking the A/T Fluid (ATF)"
.
SCIA5254E
Tool number
: ST33400001 (J-26082)
WCIA0475E
KEY INTERLOCK CABLE
TM-297
< REMOVAL AND INSTALLATION >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
KEY INTERLOCK CABLE
Component
INFOID:0000000009480683
CAUTION:
• Install key interlock cable in such a way that it will not be damaged by sharp bends, twists or interfer-
ence with adjacent parts.
• After installing key interlock cable to shift selector, make sure that casing cap and bracket are firmly
secured in their positions. If casing cap can be removed with an external load of less than 39 N (4.0
kg, 8.8 lb), replace key interlock cable with new one.
Removal and Installation
INFOID:0000000009480684
REMOVAL
1. Remove the A/T finisher. Refer to
.
2. Remove the lower glove box. Refer to
IP-23, "Removal and Installation"
.
3. Remove instrument lower panel LH. Refer to
IP-18, "Removal and Installation"
WCIA0467E
TM-298
< REMOVAL AND INSTALLATION >
[5AT: RE5R05A]
KEY INTERLOCK CABLE
4. Unlock slider from adjuster holder by squeezing lock tabs.
5. Remove casing cap from bracket of shift selector assembly and
remove interlock rod from adjuster holder.
6. Remove holder from key cylinder and remove key interlock
cable.
INSTALLATION
1. Set key interlock cable to key cylinder and install holder.
2. Set shift selector handle to “P” position.
3. Turn ignition key to "LOCK" position.
SCIA1230E
LCIA0375E
SCIA2258E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст