Nissan Frontier. Instruction — part 1270
CONTROL VALVE WITH TCM
TM-291
< REMOVAL AND INSTALLATION >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
14. Remove O-ring from A/T assembly harness connector.
CAUTION:
Do not reuse O-ring.
15. Disconnect TCM connectors.
CAUTION:
Do not damage harness connectors.
16. Remove A/T assembly harness connector from control valve
with TCM using suitable tool.
17. Disconnect harness connector (1) and (2) from TCM connector
and transmission range switch.
CAUTION:
Do not damage harness connectors.
Installation
CAUTION:
After completing installation, check A/T fluid leakage and fluid level. Refer to
.
SCIA5155E
SCIA5447E
SCIA5448E
JSDIA1317ZZ
TM-292
< REMOVAL AND INSTALLATION >
[5AT: RE5R05A]
CONTROL VALVE WITH TCM
1. Connect TCM connector (1) and transmission range switch har-
ness connector (2).
2. Install A/T assembly harness connector to control valve with
TCM.
3. Connect TCM connector.
4. Install new O-ring in A/T assembly harness connector.
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
5. Install new O-ring (1) in plug (2).
CAUTION:
• Do not reuse O-ring.
• Apply ATF to O-ring.
• O-ring should be free of contamination.
JSDIA1317ZZ
SCIA5450E
SCIA5447E
SCIA5155E
JSDIA1313ZZ
CONTROL VALVE WITH TCM
TM-293
< REMOVAL AND INSTALLATION >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
6. Install plug (2) to bracket (1).
7. Install plug (1) [with bracket (2)] to control valve with TCM.
Tighten plug bolt (
) to the specified torque.
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve with
TCM.
8. Install control valve with TCM in transmission case.
CAUTION:
• Make sure that input speed sensor is securely installed
into input speed sensor hole (A).
• Hang down output speed sensor harness toward outside
so as not to disturb installation of control valve with TCM.
• Adjust A/T assembly harness connector of control valve
with TCM to terminal hole of transmission case.
• Assemble it so that instruction valve cutout is engaged with
instruction plate projection.
9. Install bolts (A), (B) and (C) in control valve with TCM.
JSDIA1312ZZ
JSDIA1311ZZ
(1)
: Brake band
JSDIA1318ZZ
SCIA5142E
: Front
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA8074E
TM-294
< REMOVAL AND INSTALLATION >
[5AT: RE5R05A]
CONTROL VALVE WITH TCM
10. Tighten bolt (1A), (2B) and (3A) temporarily to prevent disloca-
tion. After that tighten them in order (1
→ 2 → 3). Then tighten
other bolts. Tighten control valve with TCM bolts to the specified
torque.
11. Connect output speed sensor harness connector (1).
12. Securely fasten output speed sensor (1) harness with terminal
clip (
).
13. Install oil pan to transmission case. Refer to
TM-286, "Removal and Installation"
.
14. Pull up A/T assembly harness connector.
CAUTION:
Do not damage harness connector.
: Front
Bolt symbol
A
B
C
Number of bolts
5
6
1
Length mm (in)
42 (1.65)
55 (2.17)
40 (1.57)
Tightening torque
N·m (kg-m, in-lb)
7.9 (0.81, 70)
With ATF applied
7.9 (0.81, 70)
SCIA8075E
JSDIA1319ZZ
JSDIA1316ZZ
SCIA5038E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст