Nissan Frontier. Instruction — part 310
DLN-142
< BASIC INSPECTION >
[PROPELLER SHAFT: 2S1330]
PROPELLER SHAFT ASSEMBLY
BASIC INSPECTION
PROPELLER SHAFT ASSEMBLY
Inspection
INFOID:0000000009479736
APPEARANCE AND NOISE INSPECTION
• Check the propeller shaft tube surface for dents or cracks. If damaged, replace the propeller shaft assembly.
• Check the bearings for noise and damage. Repair or replace the bearings as necessary.
PROPELLER SHAFT VIBRATION
If a vibration is present at high speed, inspect the propeller shaft runout first.
1. Measure the runout of the propeller shaft tube at several points
by rotating the final drive companion flange with your hands.
DLN-147, "General Specification"
.
2. If the runout exceeds specifications, disconnect the propeller shaft at the final drive companion flange;
then rotate the companion flange 90
°, 180° and 270° and reconnect the propeller shaft.
3. Check the runout again. If the runout still exceeds specifications, replace the propeller shaft assembly.
4. After installation, check for vibration by driving vehicle.
LDIA0161E
LDIA0121E
PROPELLER SHAFT
DLN-143
< UNIT REMOVAL AND INSTALLATION >
[PROPELLER SHAFT: 2S1330]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
UNIT REMOVAL AND INSTALLATION
PROPELLER SHAFT
Removal and Installation
INFOID:0000000009479737
COMPONENTS
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove under cover (if equipped). Refer to
EXT-15, "Removal and Installation"
.
2. Put transmission in neutral and release the parking brake.
3. Put matching marks on the rear propeller shaft flange yoke and
the rear final drive companion flange as shown.
CAUTION:
For matching marks, use paint. Do not damage the rear pro-
peller shaft flange yoke or the companion flange.
4. Remove the bolts, then remove the propeller shaft from the rear
final drive and transfer.
INSPECTION
1.
Propeller shaft tube
2.
Snap ring
3.
Journal bearing
4.
Sleeve yoke
5.
Journal
6.
Flange yoke
Front
AWBIA0800GB
WDIA0049E
DLN-144
< UNIT REMOVAL AND INSTALLATION >
[PROPELLER SHAFT: 2S1330]
PROPELLER SHAFT
• Inspect the propeller shaft runout. If runout exceeds the limit,
replace the propeller shaft assembly. Refer to
• While holding the flange yoke on one side, check axial play of the
joint as shown. If the journal axial play exceeds the specification,
repair or replace the journal parts. Refer to
• Check the propeller shaft tube for dents or cracks. If damage is
detected, replace the propeller shaft assembly.
INSTALLATION
Installation is in the reverse order of removal.
• After installation, check for vibration by driving the vehicle. Refer to
DLN-141, "NVH Troubleshooting Chart"
.
• If propeller shaft assembly or final drive assembly has been
replaced, connect them as follows:
- Face companion flange mark (A) of the final drive (1) upward. With
the mark (A) faced upward, couple the propeller shaft and the final
drive so that the matching mark (B) of the propeller shaft (2) can be
positioned as closest as possible with the matching mark (C) of the
final drive companion flange.
- Tighten propeller shaft and final drive bolts and nuts to specifica-
DLN-143, "Removal and Installation"
.
CAUTION:
Do not reuse the bolts and nuts. Always install new ones.
LDIA0121E
LDIA0117E
PDIA0892J
PROPELLER SHAFT
DLN-145
< UNIT DISASSEMBLY AND ASSEMBLY >
[PROPELLER SHAFT: 2S1330]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
UNIT DISASSEMBLY AND ASSEMBLY
PROPELLER SHAFT
Disassembly and Assembly
INFOID:0000000009479738
DISASSEMBLY
Journal
1. Put matching marks on the rear propeller shaft and flange yoke
as shown.
CAUTION:
For matching marks use paint. Do not damage the rear pro-
peller shaft or flange yoke.
2. Remove the snap rings.
CAUTION:
Do not reuse snap rings.
3. Push out and remove the journal bearings by lightly tapping the
flange yoke with a hammer, taking care not to damage the jour-
nal or flange yoke hole.
NOTE:
Put marks on the disassembled parts so that they can be rein-
stalled in their original positions from which they were removed.
4. Push out and remove the remaining journal bearings at the
opposite side by lightly tapping the flange yoke with a hammer,
taking care not to damage the journal or flange yoke hole.
NOTE:
Put marks on the disassembled parts so that they can be rein-
stalled in their original positions from which they were removed.
ASSEMBLY
SPD128
APD011
SPD732
SPD131
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст