Nissan Frontier. Instruction — part 315
DLN-162
< BASIC INSPECTION >
[3S1330]
PROPELLER SHAFT ASSEMBLY
BASIC INSPECTION
PROPELLER SHAFT ASSEMBLY
Inspection
INFOID:0000000009479754
APPEARANCE AND NOISE INSPECTION
Check the propeller shaft tube surface for dents or cracks. If damaged, replace the propeller shaft assembly.
PROPELLER SHAFT VIBRATION
If a vibration is present at high speed, inspect the propeller shaft runout first.
1. Measure the runout of the propeller shaft tube at several points
by rotating the final drive companion flange with your hands.
2. If the runout exceeds specifications, disconnect the propeller shaft at the final drive companion flange;
then rotate the companion flange 90
°, 180° and 270° and reconnect the propeller shaft.
3. Check the runout again. If the runout still exceeds specifications, replace the propeller shaft assembly.
4. After installation, check for vibration by driving vehicle.
Propeller shaft runout limit
2WD : Refer to
LDIA0161E
LDIA0121E
REAR PROPELLER SHAFT
DLN-163
< UNIT REMOVAL AND INSTALLATION >
[3S1330]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
UNIT REMOVAL AND INSTALLATION
REAR PROPELLER SHAFT
Removal and Installation
INFOID:0000000009479755
COMPONENTS
Model 3S1330
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove under cover (if equipped). Refer to
EXT-15, "Removal and Installation"
.
2. Put the transmission in neutral and release the parking brake.
3. Put matching marks on the rear propeller shaft flange yoke and
the rear final drive companion flange as shown.
CAUTION:
For matching marks, use paint. Do not damage the rear pro-
peller shaft flange yoke or the companion flange.
4. Remove the bolts, then remove the propeller shaft from the rear
final drive and transmission.
INSPECTION
AWDIA1086ZZ
1.
Propeller shaft (1st shaft)
2.
Snap ring
3.
Journal bearing
4.
Sleeve yoke (A/T)
5.
Sleeve yoke (M/T)
6.
Journal
7.
Propeller shaft (2nd shaft)
8.
Flange
Front
WDIA0049E
DLN-164
< UNIT REMOVAL AND INSTALLATION >
[3S1330]
REAR PROPELLER SHAFT
• Inspect the propeller shaft runout. If runout exceeds the limit,
replace the propeller shaft assembly.
• While holding the flange yoke on one side, check axial play of the
joint as shown. If the journal axial play exceeds the specification,
repair or replace the journal parts.
• Check the propeller shaft for dents or cracks. If damage is
detected, replace the propeller shaft assembly.
INSTALLATION
Installation is in the reverse order of removal.
• After installation, check for vibration by driving the vehicle. Refer to
DLN-161, "NVH Troubleshooting Chart"
.
CAUTION:
Do not reuse the bolts and nuts. Always install new ones.
Propeller shaft runout limit
2WD : Refer to
LDIA0121E
Journal axial play : Refer to
LDIA0117E
REAR PROPELLER SHAFT
DLN-165
< UNIT DISASSEMBLY AND ASSEMBLY >
[3S1330]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
UNIT DISASSEMBLY AND ASSEMBLY
REAR PROPELLER SHAFT
Disassembly and Assembly
INFOID:0000000009479756
DISASSEMBLY
Journal
1. Remove the propeller shaft assembly from the vehicle. Refer to
DLN-163, "Removal and Installation"
.
2. Put matching marks on the rear propeller shaft tube and flange
yoke as shown.
CAUTION:
For matching marks use paint. Do not damage the rear pro-
peller shaft or flange yoke.
3. Remove the snap rings.
CAUTION:
Do not reuse snap rings.
4. Push out and remove the journal bearing by lightly tapping the
yoke with a hammer, taking care not to damage the journal or
yoke hole.
5. Remove the bearing at the opposite side of above operation.
NOTE:
Put marks on the disassembled parts so that they can be rein-
stalled in their original positions from which they were removed.
SPD128
APD011
SPD732
SPD131
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст