Nissan Frontier. Instruction — part 1289
ASSEMBLY
TM-367
< UNIT DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• QR25DE models
- Snap ring (1)
- Retaining plate (2)
- Drive plate (3)
- Driven plate (4)
- Dish plate (5)
- Drive plate/Driven plate:5/6
• VQ40DE models
- Snap ring (1)
- Retaining plate (2)
- Drive plate (3)
- Driven plate (4)
- Dish plate (5)
- Drive plate/Driven plate:6/6
19. Assemble N-spring.
20. Install reverse brake retaining plate in transmission case.
JSDIA2359ZZ
SCIA6949E
SCIA5249E
TM-368
< UNIT DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
ASSEMBLY
21. Install snap ring in transmission case.
22. Measure clearance (A) between retaining plate and snap ring. If
not within specified clearance, select proper retaining plate.
23. Install needle bearing to transmission case.
CAUTION:
• Take care with the direction of needle bearing. Refer to
TM-322, "Location of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
.
• Apply petroleum jelly to needle bearing.
24. Install output speed sensor (1) to transmission case and tighten
bolt to specified torque.
CAUTION:
• Do not subject sensor to impact by dropping or hitting it.
• Do not disassemble sensor.
• Do not allow metal filings or any foreign material to get on
the sensor's front edge magnetic area.
• Do not place sensor in an area affected by magnetism.
SCIA2439E
Clearance “A”
: 0.7 - 1.1mm (0.028 - 0.043 in)
Retaining plate
: Refer to
SCIA3129E
SCIA5031E
: Bolt
Output speed sensor bolt : 5.8 N·m (0.59 kg-m, 51 in-lb)
JSDIA1321ZZ
ASSEMBLY
TM-369
< UNIT DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
25. Install new rear oil seal until it is flush into the rear extension
case (2WD models) using Tool or adapter case (4WD models)
using suitable tool.
CAUTION:
• Apply ATF to rear oil seal.
• Do not reuse rear oil seal.
26. Install return spring (1) to parking pawl (2).
27. Install parking pawl (with return spring) and pawl shaft to rear
extension (2WD models) or adapter case (4WD models).
28. Install parking actuator support to rear extension (2WD models)
or adapter case (4WD models).
Tool number
: ST33400001 (J-26082)
WCIA0475E
SCIA6180J
SCIA3424E
SCIA3423E
TM-370
< UNIT DISASSEMBLY AND ASSEMBLY >
[5AT: RE5R05A]
ASSEMBLY
29. Install needle bearing (1) to rear extension (2WD models) or
adapter case (4WD models).
CAUTION:
Apply petroleum jelly to needle bearing.
30. Install seal rings to output shaft.
CAUTION:
• Do not reuse seal rings.
• Apply petroleum jelly to seal rings.
31. Install parking gear to output shaft.
32. Install output shaft in transmission case.
CAUTION:
Do not mistake front of shaft for rear because both sides
look similar (thinner end is front side).
33. Install bearing race to output shaft.
SCIA6179J
SCIA5209E
SCIA5247E
SCIA5030E
SCIA5245E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст