Nissan Frontier. Instruction — part 1202
AIR BREATHER HOSE
TM-19
< REMOVAL AND INSTALLATION >
[FS5R30A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
AIR BREATHER HOSE
Removal and Installation
INFOID:0000000009480417
COMPONENTS
REMOVAL
1. Disconnect air breather hose from breather tube and transmission harness connector.
2. Bend the clip away from the transmission housing and remove air breather hose.
3. Remove the clip bolt and remove the clip from the transmission housing, if necessary.
4. Remove the breather tube bolt and the breather tube.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Make sure there are no pinched or blocked areas on the air breather hose after installation.
• When inserting the air breather hose, be sure to insert it fully until its end reaches the end of the tube
radius.
• Install the air breather hose with the paint mark side up.
• Install the air breather hose and harness to the clip to prevent separation.
1.
Air breather hose
2.
Harness
3.
Breather tube
4.
Clip
LCIA0380E
TM-20
< REMOVAL AND INSTALLATION >
[FS5R30A]
AIR BREATHER HOSE
• Push the clip so that the harness contacts the clip bolt.
TRANSMISSION ASSEMBLY
TM-21
< UNIT REMOVAL AND INSTALLATION >
[FS5R30A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
UNIT REMOVAL AND INSTALLATION
TRANSMISSION ASSEMBLY
Removal and Installation from Vehicle
INFOID:0000000009480418
COMPONENTS
NOTE:
1.
Breather hose
2.
Transmission assembly
3.
Dust cover
4.
Crossmember
5.
Insulator
A.
Refer to INSTALLATION
AWDIA0627GB
TM-22
< UNIT REMOVAL AND INSTALLATION >
[FS5R30A]
TRANSMISSION ASSEMBLY
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Disconnect the battery cable from the negative terminal. Refer to
PG-83, "Removal and Installation"
2. Remove the shift selector assembly. Refer to
TM-17, "Removal and Installation"
.
3. Remove the rear propeller shaft. Refer to
DLN-174, "Removal and Installation"
4. Remove the gusset.
5. Disconnect harness connector from the heated oxygen sensor and remove wire harness from transmis-
sion.
6. Disconnect harness connectors from the back-up lamp switch and park/neutral position (PNP) switch.
7. Remove the clutch operating cylinder from the transmission. Refer to
CL-14, "5M/T : Removal and Instal-
.
8. Remove the starter motor. Refer to
STR-35, "Removal and Installation (QR25DE)"
.
9. Support the transmission using a suitable jack.
10. Remove the transmission dust cover.
11. Remove the transmission to engine bolts.
12. Remove the nuts securing the insulator to the crossmember.
13. Remove the transmission crossmember using power tool.
WARNING:
Support the transmission using suitable jack.
14. Remove the air breather hose and breather tube. Refer to
TM-19, "Removal and Installation"
15. Separate the transmission from the engine and remove it from the vehicle.
WARNING:
Support instruction transmission while removing it using suitable jack.
INSTALLATION
Installation is in the reverse order of removal.
• When installing the transmission to the engine, install the bolts in
accordance with the standard below.
CAUTION:
• When installing be careful to avoid interference between transmission main drive gear and clutch
cover.
• When replacing an engine or transmission you must make sure the dowels are installed correctly
during re-assembly.
• Improper alignment caused by missing dowels may cause vibration oil leaks or breakage of driv-
etrain components.
• After installation, check for oil leakage and oil level. Refer to
Bolt No.
1
2
3
Quantity
4
1
6
Bolt length “ ”
mm (in)
60 (2.36)
65 (2.56)
Tightening torque
N·m (kg-m, ft-lb)
35 (3.6, 26)
75 (7.7, 55)
WCIA0505E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст