Nissan Maxima. Instruction — part 611
EXL-186
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
COMBINATION SWITCH READING SYSTEM
COMBINATION SWITCH READING SYSTEM
System Diagram
INFOID:0000000010069909
System Description
INFOID:0000000010069910
OUTLINE
• BCM reads the status of the combination switch (light, turn signal, wiper and washer) and recognizes the
status of each switch.
• BCM has a combination of 5 output terminals (OUTPUT 1 - 5) and 5 input terminals (INPUT 1 - 5) and reads
a maximum of 20 switch states.
COMBINATION SWITCH MATRIX
Combination switch circuit
Combination switch INPUT-OUTPUT system list
AWMIA1215GB
System
INPUT 1
INPUT 2
INPUT 3
INPUT 4
INPUT 5
OUTPUT 1
—
FR WASHER
FR WIPER LOW
TURN LH
TURN RH
OUTPUT 2
FR WIPER HI
—
FR WIPER INT
PASSING
HEADLAMP 1
OUTPUT 3
INT VOLUME 1
—
—
HEADLAMP 2
HI BEAM
AWMIA1216GB
COMBINATION SWITCH READING SYSTEM
EXL-187
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
COMBINATION SWITCH READING FUNCTION
Description
• BCM reads the status of the combination switch at 10ms intervals normally.
NOTE:
BCM reads the status of the combination switch at 60ms intervals when BCM is controlled at low power con-
sumption mode.
• BCM operates as follows and judges the status of the combination switch.
- It operates the transistor on OUTPUT side in the following order: OUTPUT 1
→ 2 →3 →4 →5 and outputs
voltage waveform.
- The voltage waveform of OUTPUT corresponding to the formed circuit is input into the interface on INPUT
side if any (1 or more) switches are ON.
- It reads this change of the voltage as the status signal of the combination switch.
Operation Example
OUTPUT 4
—
INT VOLUME 3
AUTO LIGHT
—
TAIL LAMP
OUTPUT 5
INT VOLUME 2
—
—
FR FOG
—
System
INPUT 1
INPUT 2
INPUT 3
INPUT 4
INPUT 5
JPMIA0609GB
JMMIA0326GB
EXL-188
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
COMBINATION SWITCH READING SYSTEM
In the following operation example, the combination of the status signals of the combination switch is replaced
as follows: INPUT 1 - 5 to “1 - 5” and OUTPUT 1 - 5 to “A - E”.
Example 1: When a switch (TAIL LAMP) is turned ON
• The circuit between OUTPUT 4 and INPUT 5 is formed when the TAIL LAMP is turned ON.
• BCM detects the combination switch status signal “5D” when the signal of OUTPUT 4 is input to INPUT 5.
• BCM judges that the TAIL LAMP switch is ON when the signal “5D” is detected.
Example 2: When some switches (TRUN RH, TAIL LAMP) are turned ON
• The circuits between OUTPUT 1 and INPUT 5 and between OUTPUT 4 and INPUT 5 are formed when the
TURN RH switch and TAIL LAMP switch are turned ON.
• BCM detects the combination switch status signal “5AD” when the signals of OUTPUT 1 and OUTPUT 4 are
input to INPUT 5.
• BCM judges that the TURN RH switch and TAIL LAMP switch are ON when the signal “5AD” is detected.
WIPER INTERMITTENT DIAL POSITION SETTING (FRONT WIPER INTERMITTENT OPERATION)
BCM judges the wiper intermittent dial 1 - 7 by the status of INT VOLUME 1, 2, and 3 switches.
AWMIA1217GB
AWMIA1218GB
COMBINATION SWITCH READING SYSTEM
EXL-189
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Wiper intermittent dial posi-
tion
Intermittent oper-
ation delay inter-
val
INT VOLUME switch ON/OFF status
INT VOLUME 1 switch
INT VOLUME 2 switch
INT VOLUME 3 switch
1
Short
↑
↓
Long
ON
ON
ON
2
ON
ON
OFF
3
ON
OFF
OFF
4
OFF
OFF
OFF
5
OFF
OFF
ON
6
OFF
ON
ON
7
OFF
ON
OFF
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст