Nissan Maxima. Instruction — part 1121
HYDRAULIC LINE
ST-29
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
HYDRAULIC LINE
Exploded View
INFOID:0000000009465784
1.
High pressure hose
2.
Suction hose
3.
Reservoir tank bracket
4.
Reservoir tank
5.
Oil pump assembly
6.
Steering gear assembly
7.
Low pressure piping
8.
Eye bolt
9.
High pressure piping
10. Copper sealing washers
11. Eye bolt
12.
Copper sealing washers
13. Power steering pressure sensor
14. High pressure hose piping
15.
Power steering fluid cooler
AWGIA0189GB
ST-30
< REMOVAL AND INSTALLATION >
HYDRAULIC LINE
Removal and Installation
INFOID:0000000009465785
CAUTION:
• Securely insert harness connector to pressure sensor.
• Do not reuse O-rings or copper sealing washers.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
for removal.
INSTALLATION
• Insert hose securely until it contacts tube spool.
CAUTION:
Do not use lubricant on hose or fitting.
• Install eye-bolt (1), copper sealing washers (2) and eye-joint
(assembled to high-pressure hose) (4) onto oil pump assembly (3),
and temporarily tighten the eye-bolt, then tighten it to the specified
torque.
CAUTION:
Do not reuse copper sealing washers.
16. O-ring
Front
A.
View A
B.
View B
SGIA0514E
AWGIA0106ZZ
STEERING COLUMN
ST-31
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
UNIT DISASSEMBLY AND ASSEMBLY
STEERING COLUMN
Disassembly and Assembly
INFOID:0000000009465786
The steering column assembly without electric motor is not serviceable and must be replaced as an assembly.
With Electric Motor
DISASSEMBLY
1. Remove the steering wheel. Refer to
ST-17, "Removal and Installation"
Tilt motor
1. Remove the tilt motor as follows.
1. Disconnect the harness connector (A) from the tilt motor.
2. Remove the tilt motor link bolts (B).
ALGIA0054GB
1.
Steering column assembly
2.
Telescope motor
3.
Telescope motor link bracket
4.
Tilt motor
5.
Tilt motor bolt cap
ALGIA0051ZZ
ST-32
< UNIT DISASSEMBLY AND ASSEMBLY >
STEERING COLUMN
3. Remove the tilt motor bolt (A) from the RH side of column.
4. Remove the tilt motor (B).
NOTE:
If the steering wheel could not be tilted to the highest position,
instructionly tilt steering wheel to the highest position.
Telescope motor
1. Remove telescope motor as follows.
1. Disconnect the harness connector (A) from the telescope
motor.
2. Remove the two telescope motor link screws (B) and tele-
scope motor link bracket.
3. Remove telescope motor bolt (C).
4. Remove the telescope motor (D).
NOTE:
If the steering wheel could not be telescoped to full out posi-
tion instructionly pull steering wheel to the full out position
ASSEMBLY
Assembly is in the reverse order of removal
NOTE:
• Upon installation of the tilt motor link bolts instructionly move steering wheel up and down to align the bolts.
• Adjust the telescope motor link to full out position and adjust as needed to fit into proper installed position.
• Inform customer that they will need to reset their Automatic Drive Positioner (ADP) settings.
ALGIA0052ZZ
ALGIA0053ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст