Nissan Maxima. Instruction — part 89
AV-176
< REMOVAL AND INSTALLATION >
[MONOCHROME DISPLAY - W/ BOSE]
TEL ANTENNA
TEL ANTENNA
Removal and Installation
INFOID:0000000009471276
REMOVAL
1. Disconnect the battery negative terminal. Refer to
PG-67, "Removal and Installation (Battery)"
2. Remove the rear parcel shelf finisher. Refer to
INT-28, "Removal and Installation"
.
3. Remove the Bluetooth antenna screw (A).
4. Detach the Bluetooth antenna harness clip (B).
5. Fold down the rear seat (if equipped) or open the trunk lid, then
detach the Bluetooth antenna harness clip (C).
6. Disconnect the harness connector (D) from the Bluetooth
antenna (1) and remove.
INSTALLATION
Installation is in the reverse order of removal.
ALNIA1144ZZ
AV
BLUETOOTH CONTROL UNIT
AV-177
< REMOVAL AND INSTALLATION >
[MONOCHROME DISPLAY - W/ BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
BLUETOOTH CONTROL UNIT
Removal and Installation
INFOID:0000000009471277
REMOVAL
1. Disconnect the battery negative terminal. Refer to
PG-67, "Removal and Installation (Battery)"
2. Remove the trunk upper finisher. Refer to
3. Remove the parcel shelf finisher. Refer to
INT-28, "Removal and Installation"
4. From inside the passenger compartment, remove the bracket screws and lower the assembly for access.
5. Remove the Bluetooth control unit screws (A).
6. Disconnect the harness connector (B) from the Bluetooth control
unit and remove.
INSTALLATION
Installation is in the reverse order of removal.
ALNIA1154ZZ
AV-178
< BASIC INSPECTION >
[COLOR DISPLAY - W/O BOSE]
DIAGNOSIS AND REPAIR WORKFLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
INFOID:0000000010064809
OVERALL SEQUENCE
AV-202, "CONSULT Function (MULTI AV)"
DETAILED FLOW
1.
CHECK SYMPTOM
Check the malfunction symptoms by performing the following items.
• Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-
tion occurred).
• Check the symptom.
>> GO TO 2
2.
SELF-DIAGNOSIS (CONSULT)
1. Connect CONSULT and perform “SELF-DIAGNOSIS” for “MULTI AV”.
NOTE:
Skip to step 4 of the diagnosis procedure if “MULTI AV” is not displayed.
2. Check if any DTC No. is displayed in the self-diagnosis results.
AWNIA2486GB
AV
DIAGNOSIS AND REPAIR WORKFLOW
AV-179
< BASIC INSPECTION >
[COLOR DISPLAY - W/O BOSE]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
Is any DTC No. displayed?
YES
>> GO TO 3
NO
>> GO TO 4
3.
CHECK SELF-DIAGNOSIS RESULTS (CONSULT)
1. Check the DTC No. indicated in the self-diagnosis results.
2. Perform the relevant diagnosis referring to the DTC No. list. Refer to
NOTE:
Start with the diagnosis for the CAN communication system if “CAN COMM CIRCUIT [U1000] or CONTROL
UNIT (CAN) [U1010]” is displayed.
>> GO TO 5
4.
PERFORM DIAGNOSIS BY SYMPTOM
Perform the relevant diagnosis referring to the diagnosis chart by symptom. Refer to
.
>> GO TO 5
5.
REPAIR OR REPLACE MALFUNCTIONING PARTS
Repair or replace the identified malfunctioning parts.
NOTE:
Erase the stored self-diagnosis results after repairing or replacing the relevant components if any DTC No. has
been indicated in the self-diagnosis results.
>> GO TO 6
6.
CHECK AFTER REPAIR
1. Perform self-diagnosis for “MULTI AV” with CONSULT after repairing or replacing the malfunctioning
parts.
2. Check if any DTC No. is displayed in the self-diagnosis results.
Is any DTC No. displayed?
YES
>> GO TO 3
NO
>> GO TO 7
7.
FINAL CHECK
Perform the operation check to confirm that the malfunction symptom is solved or that any other symptoms
are present.
Are any symptoms present?
YES
>> GO TO 4
NO
>> Inspection End.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст