Nissan Maxima. Instruction — part 373
FRONT FENDER
DLK-211
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT FENDER
Exploded View
INFOID:0000000009471764
Removal and Installation
INFOID:0000000009471765
REMOVAL
1. Remove the front combination lamp. Refer to
EXL-154, "Removal and Installation"
.
2. Remove the fender protector. Refer to
EXT-24, "Removal and Installation"
3. Remove cowl top side trim cover.
EXT-21, "Removal and Installation"
4. Remove the bolts and the front fender.
CAUTION:
• Use shop cloths to protect the body from being damaged during removal and installation.
• Use care when removing the front fender. The front fender baffle foam adheres the front fender
to the body side outer. Carefully release the baffle foam or damage to the front fender may occur.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation apply touch up paint (body color) to the head of front fender bolts.
• After installation, adjust the following components as necessary:
- Hood assembly: Refer to
DLK-203, "HOOD ASSEMBLY : Adjustment"
.
- Front door: Refer to
DLK-215, "FRONT DOOR : Adjustment"
Adjustment
INFOID:0000000009471766
ADJUSTMENT
1.
Front fender
AWKIA1337ZZ
DLK-212
< REMOVAL AND INSTALLATION >
FRONT FENDER
Unit: mm (in)
1.
Front fender
2.
Front fascia
3.
Body side outer
4.
Front door assembly
Section
Item
Measurement
Standard
Parallelism
Equality
A-A
E
Clearance
2.35
± 1.0 (0.093 ± 0.04)
≤ 1.0 (0.04)
—
F
Surface height
0.7
± 1.0 (0.028 ± 0.04)
≤ 1.0 (0.04)
≤ 1.0 (0.04)
AWKIA1338ZZ
FRONT FENDER
DLK-213
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1. Remove the fender protector. Refer to
EXT-24, "Removal and Installation"
2. Loosen the front fender bolts and screws.
3. Adjust the clearance (M) and surface height (N) between the front fender and the front door.
4. Tighten the rear upper and lower front fender bolts.
5. Adjust the clearance (E) and surface height (F) between the front fender and the body side outer.
6. Tighten the inner front fender bolts.
7. Adjust the clearance (J) and the surface height (K) between the top of the front fender and the top of the
front fascia.
8. Adjust the clearance (G) and surface height (H) between the side of the front fender and the side of the
front fascia.
9. Tighten the front fender to front fascia and bracket screws.
10. Apply touch-up paint (body color) to the head of the front fender bolts.
11. Install the fender protector. Refer to
EXT-24, "Removal and Installation"
.
12. Install the inner fender bolt cover.
B-B
G
Clearance
0.0 + 0.08, - 0.0 (0.0 + 0.003, - 0.0)
—
—
H
Surface height
0.7
± 1.3 (0.028 ± 0.05)
≤ 2.0 (0.08)
≤ 2.0 (0.08)
C-C
J
Clearance
0.0 + 0.07, - 0.0 (0.0 + 0.003, - 0.0)
≤ 1.0 (0.04)
≤ 1.0 (0.04)
K
Surface height
-0.24
± 1.0 (-0.01 ± 0.04)
≤ 1.5 (0.06)
≤ 2.0 (0.08)
D-D
M
Clearance
4.25
± 1.0 (0.17 ± 0.04)
—
—
N
Surface height
0.0
± 1.0 (0.0 ± 0.04)
—
—
Section
Item
Measurement
Standard
Parallelism
Equality
DLK-214
< REMOVAL AND INSTALLATION >
DOOR
DOOR
FRONT DOOR
FRONT DOOR : Exploded View
INFOID:0000000009471767
FRONT DOOR : Removal and Installation
INFOID:0000000009471768
CAUTION:
• Use two people when removing or installing the front door assembly due to its heavy weight.
• When removing and installing front door assembly, support front door with a suitable tool.
REMOVAL
1. Pull the grommet and wire harness out of the front pillar until the harness connectors are accessible. Then
disconnect the wire harness connectors.
2. Remove the check link bolt from the front pillar.
1.
Front door panel
2.
Front door check link
3.
Front door lower hinge
4.
Front lower hinge
Grease
ALKIA2792ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст