Nissan Maxima. Instruction — part 877

    MWI

    METER CONTROL SWITCH

    MWI-123

    < REMOVAL AND INSTALLATION >

    C

    D

    E

    F

    G

    H

    I

    J

    K

    L

    M

    B

    A

    O

    P

    METER CONTROL SWITCH

    Removal and Installation

    INFOID:0000000009465122

    REMOVAL

    1. Disconnect the negative battery terminal. Refer to

    PG-67, "Removal and Installation (Battery)"

    .

    2. Remove the cluster lid A. Refer to

    IP-16, "Removal and Installation"

    .

    3. Detach the combination meter control switch harness clips (A).
    4. Remove the combination meter control switch screws (B) and

    remove the combination meter control switch (1).

    INSTALLATION

    Installation is in the reverse order of removal.

    ALNIA1138ZZ

    MWI-124

    < UNIT DISASSEMBLY AND ASSEMBLY >

    COMBINATION METER

    UNIT DISASSEMBLY AND ASSEMBLY

    COMBINATION METER

    Disassembly and Assembly

    INFOID:0000000009465123

    DISASSEMBLY

    1. Remove the combination meter. Refer to

    MWI-122, "Removal and Installation"

    .

    2. Remove the combination meter lens (1) from the combination

    meter (2).

    ASSEMBLY

    Assembly is in the reverse order of disassembly.

    ALLIA0007ZZ

    PB-2

    < PRECAUTION >

    PRECAUTIONS

    PRECAUTION

    PRECAUTIONS

    Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
    PRE-TENSIONER"

    INFOID:0000000009466619

    The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along

    with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain

    types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS

    system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front

    air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.

    Information necessary to service the system safely is included in the SR and SB section of this Service Man-

    ual.

    WARNING:

    • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

    the event of a collision which would result in air bag inflation, all maintenance must be performed by

    an authorized NISSAN/INFINITI dealer.

    • Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

    injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag

    Module, see the SR section.

    • Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this

    Service Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-

    ness connectors.

    PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

    WARNING:

    • When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-

    tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a

    hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing

    serious injury.

    • When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the

    battery and wait at least 3 minutes before performing any service.

    Была ли эта страница вам полезна?
    Да!Нет
    8 посетителей считают эту страницу полезной.
    Большое спасибо!
    Ваше мнение очень важно для нас.

    Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.

    Текст

    Матвей Александрович28.05.2024 23:59
    Политика конфиденциальности