Nissan Maxima. Instruction — part 878
PREPARATION
PB-3
< PREPARATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000009466620
Tool name
Description
Brake drum clearance gauge
Measuring rear rotor drum inner diameter
Power tool
Loosening nuts, screws and bolts
WFIA0167E
PIIB1407E
PB-4
< PERIODIC MAINTENANCE >
PARKING BRAKE SYSTEM
PERIODIC MAINTENANCE
PARKING BRAKE SYSTEM
On-Vehicle Service
INFOID:0000000009466621
PEDAL STROKE
• When parking brake pedal is operated with the specified force, make sure the stroke is within the specified
number of notches. Check by listening and counting the ratchet clicks.
INSPECTION
• Make sure the components are attached properly, checking for looseness or backlash.
• Check parking brake pedal assembly for bends, damage and cracks, and replace if necessary.
• Check cable for wear and damage, and replace if necessary.
• Check parking brake warning lamp switch for malfunction, and replace if necessary. Refer to
ADJUSTMENT
1. Remove the instrument lower panel LH. Refer to
IP-19, "Removal and Installation"
.
2. Partially engage parking brake pedal to access adjusting nut.
3. Insert a deep socket wrench to rotate adjusting nut and loosen
cable sufficiently. Then, disengage the parking brake pedal.
4. Remove the wheel and tire using power tool. Using at least two wheel nuts, secure the disc rotor to the
hub to prevent it from tilting.
5. Remove the adjusting hole plug from the disc rotor. Turn the
adjuster (1) in the direction (A) as shown using a suitable tool
until the disc rotor is locked.
6. Turn the adjuster (1) back 5 or 6 notches from the locked posi-
tion in the direction (B) as shown using a suitable tool.
Pedal stroke
: Refer to
PB-11, "Parking Brake Control"
.
WFIA0165E
JPFIB0002ZZ
JPFIB0007ZZ
PARKING BRAKE SYSTEM
PB-5
< PERIODIC MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
7. Rotate the disc rotor to make sure there is no drag.
8. Adjust cable as follows:
a. Operate pedal 10 or more times with a force of 490 N (50 kg, 110 lb).
b. Rotate adjusting nut with deep socket to adjust pedal stroke to specification.
CAUTION:
Do not reuse the adjusting nut if it is removed.
c. With parking brake pedal completely disengaged, make sure there is no drag on the parking brake.
9. Install the wheel and tire using power tool. Refer to
.
10. Install the instrument lower panel LH. Refer to
IP-19, "Removal and Installation"
Pedal stroke
: Refer to
PB-11, "Parking Brake Control"
.
PB-6
< REMOVAL AND INSTALLATION >
PARKING BRAKE CONTROL
REMOVAL AND INSTALLATION
PARKING BRAKE CONTROL
Exploded View
INFOID:0000000009466622
Removal and Installation
INFOID:0000000009466623
REMOVAL
1. Remove rear wheel and tire using power tool. Refer to
.
2. Remove instrument lower panel LH. Refer to
IP-19, "Removal and Installation"
.
1.
Parking brake pedal
2.
Parking brake switch
3.
Pedal pad
4.
Adjusting nut
5.
Lock plate
6.
Front cable
7.
Rear cable (RH)
8.
Rear cable (LH)
9.
Equalizer
10. Spring
11. Pin
Front
AWFIA0941ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст