Nissan Juke F15. Instruction — part 245
DLK-160
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
8. While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
9. Remove front gasket (1) and rear gasket (2).
10. Slide outside handle bracket toward rear of vehicle to remove.
11. Disconnect outside handle cable (1) from outside handle bracket
(2).
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• When installing key rod, rotate key rod holder until a click is felt.
• Check that door lock cables are normally engaged with inside handle and outside handle.
• After installation, check door open/close, and lock/unlock operation.
JMKIA0524ZZ
: Vehicle front
JMKIA5889ZZ
: Vehicle front
JMKIA5890ZZ
JMKIA5891ZZ
REAR DOOR LOCK
DLK-161
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REAR DOOR LOCK
Exploded View
INFOID:0000000012196738
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000012196739
REMOVAL
1. Remove rear door glass and rear door lower sash (rear). Refer to
GW-21, "Removal and Installation"
.
2. Remove inside handle. Refer to
DLK-162, "INSIDE HANDLE : Removal and Installation"
.
3. Remove outside handle. Refer to
DLK-162, "OUTSIDE HANDLE : Removal and Installation"
.
4. Remove door lock assembly TORX bolts.
5. Disconnect door lock actuator connector, and then remove door lock assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse TORX bolt. Always replace it with a new one when it is removed.
• Check door open/close, lock/unlock operation after installation.
1.
Outside handle assembly
2.
Rear door sealing screen
3.
Door lock assembly
4.
TORX bolt
5.
Inside handle
: Clip
: Pawl
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Body grease
JMKIA5893GB
DLK-162
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
• Check door lock assembly for poor lubrication. Apply body
grease to door lock if necessary.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000012196740
REMOVAL
1. Remove rear door finisher. Refer to
INT-16, "Removal and Installation"
.
2. Remove upper side of sealing screen.
NOTE:
Cut the butyl tape so that some parts of the butyl tape do not remain on the sealing screen, if the sealing
screen is reused.
3. Remove inside handle mounting bolt (A).
4. Disengage inside handle (1) from door panel (2) while sliding
inside handle toward vehicle rear, and then separate inside han-
dle.
5. Disengage inside handle cable (3) and lock knob cable (2), and
then remove inside handle (1).
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000012196741
REMOVAL
1. Remove rear door finisher and rear door corner cover inner. Refer to
INT-16, "Removal and Installation"
2. Remove rear door sealing screen.
: Grease up point
JMKIA5892ZZ
: Vehicle front
JMKIA5884ZZ
JMKIA5885ZZ
REAR DOOR LOCK
DLK-163
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3. Rotate stopper (1) upward.
4. Disengage outside handle cable (2), and then remove outside
handle cable from outside handle assembly (3).
5. Remove outside handle assembly mounting bolts (A).
6. Disengage mounting clips using a remover tool (A), and then
remove outside handle assembly.
CAUTION:
Apply protective tape (B) on the door panel to protect the
painted surface from damage.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse rear door sealing screen. Always replace it with a new one when it is removed.
When installing rear door sealing screen, install it according to the following procedure.
- Put lower portion of rear door sealing screen (1) into inside of
door panel (2).
- Perform positioning according to the following procedure,
and then install rear door sealing screen.
• Align upper portion of rear door sealing screen to hole (A) of
door panel as shown in the figure.
• Align hole of rear door sealing screen to edge (B) of door
panel as shown in the figure.
• Be careful to position outside handle cable normally when installing it. For details, refer to
.
• Check door open/close, lock/unlock operation after installation.
JMKIA5894ZZ
JMKIA5895ZZ
: Clip
JMKIA5896ZZ
JMKIA5897ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст