Nissan Juke F15. Instruction — part 140
WHEEL SENSOR
BRC-151
< REMOVAL AND INSTALLATION >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
• Never twist rear wheel sensor harness when installing rear wheel
sensor. Check that grommet (2) is fully inserted to bracket (1).
Check that rear wheel sensor harness is not twisted after installa-
tion.
CAUTION:
Check that the identification line (A) of the rear wheel sensor
is faced upward.
JPFIC0209ZZ
JPFIC0198ZZ
BRC-152
< REMOVAL AND INSTALLATION >
[WITH VDC]
SENSOR ROTOR
SENSOR ROTOR
FRONT SENSOR ROTOR
FRONT SENSOR ROTOR : Removal and Installation
INFOID:0000000012199757
REMOVAL
Replace wheel hub as an assembly when replacing because sensor rotor cannot be disassembled.
• Except NISMO RS: Refer to
FAX-66, "Removal and Installation"
• NISMO RS: Refer to
FAX-11, "Removal and Installation"
.
INSTALLATION
Replace wheel hub as an assembly when replacing because sensor rotor cannot be disassembled.
• Except NISMO RS: Refer to
FAX-66, "Removal and Installation"
• NISMO RS: Refer to
FAX-11, "Removal and Installation"
.
REAR SENSOR ROTOR
REAR SENSOR ROTOR : Removal and Installation
INFOID:0000000012199758
REMOVAL
2WD
Replace wheel hub as an assembly when replacing because sensor rotor cannot be disassembled. Refer to
RAX-7, "Removal and Installation"
.
AWD
1. Remove drive shaft. Refer to
RAX-19, "Removal and Installation"
2. Remove sensor rotor from drive shaft. Refer to
RAX-20, "WHEEL SIDE : Disassembly and Assembly"
INSTALLATION
Note the following, and install in the reverse order of the removal.
• Never reuse sensor rotor. (AWD)
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
BRC-153
< REMOVAL AND INSTALLATION >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Exploded View
INFOID:0000000012199759
Removal and Installation
INFOID:0000000012199760
REMOVAL
1. Disconnect battery cable from negative terminal.
2. Drain brake fluid. Refer to
3. Remove bracket A.
1.
ABS actuator and electric unit (con-
trol unit)
2.
Bracket A
3.
Bracket B
4.
ABS actuator and electric unit (con-
trol unit) harness connector
A. To front LH caliper
B. To rear RH caliper
C. To rear LH caliper
D. To front RH caliper
E. To master cylinder secondary side
F.
To master cylinder primary side
: Vehicle front
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JSFIA0655GB
BRC-154
< REMOVAL AND INSTALLATION >
[WITH VDC]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
4. Disconnect ABS actuator and electric unit (control unit) harness
connector (1), follow the procedure described below.
a. Push the pawl (A).
b. Move the lever (B) in the direction (C) until locked.
c.
Disconnect ABS actuator and electric unit (control unit) harness
connector.
5. Loosen flare nut of brake tube using a flare nut wrench, and then
remove brake tube from ABS actuator and electric unit (control
unit). Refer to
BR-23, "FRONT : Exploded View"
6. Remove ABS actuator and electric unit (control unit) and bracket
B.
CAUTION:
• Never remove and never install ABS actuator and electric unit (control unit) by holding harness
connector.
• Be careful not to drop ABS actuator and electric unit (control unit) and apply excessive impact to
it.
7. Remove bracket B and bushing from ABS actuator and electric unit (control unit).
INSTALLATION
Note the following, and install in the reverse order of removal.
• When replacing with a new ABS actuator and electric unit (control unit), never remove the protector of the
brake tube mounting hole until right before the brake tube is installed.
• When installing brake tube, tighten to the specified torque using a crowfoot and torque wrench so that flare
nut and brake tube are not damaged. Refer to
BR-23, "FRONT : Exploded View"
.
• Never remove and install ABS actuator and electric unit (control unit) by holding actuator harness.
• Bleed air from brake piping after installation. Refer to
BR-13, "Bleeding Brake System"
.
• Never apply excessive impact to actuator, such as by dropping it.
• After installing the ABS actuator and electric unit (control unit) har-
ness connector (1), move the lever (A) in the direction (B) to
secure the locking.
• Perform steering angle sensor neutral position adjustment when
ABS actuator and electric unit (control unit) is replaced. Refer to
JPFIC0194ZZ
JPFIC0195ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст