Nissan Juke F15. Instruction — part 898
MAP LAMP
INL-47
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000012197024
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage.
• Never touch the glass surface of the bulb with bare hands or allow oil or grease to get on it for pre-
venting damage to the bulb.
• The surface of the bulb is very hot just after the lamp is turned OFF. Never touch the glass surface of
the bulb with bare hands for preventing burns.
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (due to dirt or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
MAP LAMP BULB
1. Disengage lens fixing pawls using a remover tool (A), and then
remove lens (1).
CAUTION:
• Use a remover tool wrapped in tape.
• Insert a remover tool into the gap between bulb housing
and lens.
2. Remove bulb.
: Pawl
JMLIA1063ZZ
INL-48
< REMOVAL AND INSTALLATION >
GLOVE BOX LAMP
GLOVE BOX LAMP
Exploded View
INFOID:0000000012197025
Removal and Installation
INFOID:0000000012197026
Replacement
INFOID:0000000012197027
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage.
• Never touch the glass surface of the bulb with bare hands or allow oil or grease to get on it for pre-
venting damage to the bulb.
• The surface of the bulb is very hot just after the lamp is turned OFF. Never touch the glass surface of
the bulb with bare hands for preventing burns.
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (due to dirt or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
GLOVE BOX LAMP BULB
1. Remove glove box assembly. Refer to
IP-13, "Removal and Installation"
2. Rotate the bulb & socket assembly counterclockwise and unlock
it, and then remove bulb & socket assembly.
1.
Bulb housing
2.
Bulb & socket assembly
3.
Glove box assembly
: Pawl
: Vehicle front
JMLIA3198ZZ
JMLIA1528ZZ
LUGGAGE ROOM LAMP
INL-49
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
LUGGAGE ROOM LAMP
Exploded View
INFOID:0000000012197028
Removal and Installation
INFOID:0000000012197029
REMOVAL
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage.
• When removing, always use a remover tool that is made of plastic to prevent damage to the parts.
1. Disengage luggage room lamp fixing pawl using a remover tool
(A) according to numerical order 1
→2 indicated by the arrows as
shown in the figure.
CAUTION:
Insert a remover tool into the gap between luggage room
lamp and luggage side lower finisher RH.
2. Disconnect luggage room lamp harness connector, and then remove luggage room lamp.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000012197030
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage.
• Never touch the glass surface of the bulb with bare hands or allow oil or grease to get on it for pre-
venting damage to the bulb.
• The surface of the bulb is very hot just after the lamp is turned OFF. Never touch the glass surface of
the bulb with bare hands for preventing burns.
1.
Shade
2.
Bulb
3.
Lens
: Pawl
JMLIA1238ZZ
: Pawl
JMLIA1280ZZ
INL-50
< REMOVAL AND INSTALLATION >
LUGGAGE ROOM LAMP
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (due to dirt or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
LUGGAGE ROOM LAMP BULB
1. Remove luggage room lamp. Refer to
INL-49, "Removal and Installation"
2. Disengage shade fixing pawls using a remover tool (A) accord-
ing to the direction indicated by the arrow as shown in the figure.
CAUTION:
Use remover tool wrapped in tape.
3. Remove shade, and then remove bulb.
: Pawl
JMLIA1700ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст