Nissan Juke F15. Instruction — part 897
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
INL-43
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
Description
INFOID:0000000012197018
Provides the power supply and the ground to control the push-button ignition switch illumination.
Component Function Check
INFOID:0000000012197019
1.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION OPERATION
CONSULT ACTIVE TEST
1. Turn the ignition switch ON.
2. Select “ENGINE SW ILLUMI” of BCM (INTELLIGENT KEY) active test item.
3. With operating the test items, check that the push-button ignition switch illumination turns ON/OFF.
Does the push-button ignition switch illumination turn ON/OFF?
YES
>> Push-button ignition switch illumination circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012197020
1.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION POWER SUPPLY OUTPUT
CONSULT ACTIVE TEST
1. Turn ignition switch ON.
2. Select ENGINE SW ILLUMI of BCM (INTELLIGENT KEY) active test item.
3. With operating the test item, check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
2.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION GROUND
CONSULT ACTIVE TEST
With operating the test item, check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO-1 >> Continuity exists and remains unchanged: GO TO 4.
NO-2 >> Continuity does not exist and remains unchanged: Replace BCM. Refer to
3.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector and push-button ignition switch connector.
On
: Push-button ignition switch illumination ON
Off
: Push-button ignition switch illumination OFF
(+)
(–)
Condition
Voltage
BCM
Connector
Terminal
M70
90
Ground
ENGINE SW ILLUMI
On
12 V
Off
0 V
BCM
Ground
Test item
Continuity
Connector
Terminal
M70
92
ENGINE SW ILLUMI
On
Existed
Off
Not existed
INL-44
< DTC/CIRCUIT DIAGNOSIS >
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
3. Check continuity between BCM harness connector and push-button ignition switch harness connector.
Is the inspection result normal?
YES
>> Replace push-button ignition switch.
NO
>> Repair or replace harnesses.
4.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION SHORT CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector and push-button ignition switch connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Repair or replace harnesses.
BCM
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
M70
90
M101
5
Existed
BCM
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
M70
92
M101
6
Existed
Push-button ignition switch
Ground
Continuity
Connector
Terminal
M70
92
Not existed
INTERIOR LIGHTING SYSTEM SYMPTOMS
INL-45
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
SYMPTOM DIAGNOSIS
INTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000012197021
NOTE:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any
DTC is detected.
Symptom
Possible cause
Inspection item
All the following lamps do not turn ON.
• Map lamp
• Luggage room lamp
• Harness between BCM and each
interior room lamp
• BCM
Interior room lamp power supply cir-
cuit
Refer to
.
• Interior room lamp does not turn ON even
though the door is open.
(It turns ON when turning the interior room
lamp ON.)
• Interior room lamp does not turn OFF even
though the door is closed.
• Harness between BCM and each
door switch
• Harness between BCM and each
interior room lamp
• BCM
Door switch circuit
Refer to
.
Interior room lamp control circuit
Refer to
.
Interior room lamp timer does not activate.
(It turns ON/ OFF when the door opens/closes.)
—
Check the interior room lamp setting.
Refer to
.
• Luggage room lamp does not turn ON even
though the back door is open.
• Luggage room lamp does not turn OFF even
though the back door is closed.
• Harness between BCM and back
door switch
• Harness between BCM and lug-
gage room lamp
• BCM
Back door switch circuit
Refer to
.
Luggage room lamp circuit
Refer to
.
Push-button ignition switch illumination does not
illuminate.
• Harness between BCM and push-
button ignition switch
• BCM
Push-button ignition switch illumina-
tion circuit
Refer to
.
Interior room lamp battery saver does not acti-
vate.
BCM
Replace BCM.
Refer to
INL-46
< REMOVAL AND INSTALLATION >
MAP LAMP
REMOVAL AND INSTALLATION
MAP LAMP
Exploded View
INFOID:0000000012197022
Removal and Installation
INFOID:0000000012197023
REMOVAL
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage.
1. Disengage lens fixing pawls using a remover tool (A), and then
remove lens (1).
CAUTION:
• Use a remover tool wrapped in tape.
• Insert a remover tool into the gap between bulb housing
and lens.
2. Disengage bulb housing (1) fixing pawl using a remover tool (A)
according to numerical order 1
→2 indicated by the arrows as
shown in the figure.
CAUTION:
Use a remover tool wrapped in tape.
3. Disconnect map lamp harness connector, and then remove bulb housing.
1.
Bulb housing
2.
Bulb
3.
Lens
: Pawl
JMLIA1062ZZ
: Pawl
JMLIA1063ZZ
: Pawl
JMLIA1064ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст