Nissan Juke F15. Instruction — part 1386
WW-40
< SYMPTOM DIAGNOSIS >
WIPER AND WASHER SYSTEM SYMPTOMS
Front wiper does not
operate normally
Intermittent adjust-
ment cannot be per-
formed
• Combination switch
• Harness between combination switch and BCM
• BCM
.
BCM
—
Intermittent control
linked with vehicle
speed cannot be per-
formed
Check the wiper setting is linked with vehicle speed.
Refer to
WW-14, "WIPER : CONSULT Function - WIPER"
Service positioning
operation does not
operate
• Combination switch
• BCM
• IPDM E/R
.
Wiper is not linked to
the washer operation
• Combination switch
• Harness between combination switch and BCM
• BCM
.
BCM
—
Does not return to
stop position [Re-
peatedly operates for
10 seconds and then
stops for 20 seconds.
After that, it stops the
operation. (Fail-
safe)]
• IPDM E/R
• Harness between IPDM E/R and front wiper
motor
• Front wiper motor
Front wiper stop position sig-
nal circuit
Refer to
Rear wiper does not
operate
ON only
• Combination switch
• Harness between combination switch and BCM
• BCM
.
INT only
• Combination switch
• Harness between combination switch and BCM
• BCM
.
ON and INT
• Combination switch
• Harness between combination switch and BCM
• BCM
.
• BCM
• Harness between rear wiper motor and BCM
• Harness between rear wiper motor and ground
• Rear wiper motor
Rear wiper motor circuit
Refer to
Rear wiper does not
stop
ON only
• Combination switch
• BCM
.
INT only
• Combination switch
• BCM
.
Rear wiper does not
operate normally
Wiper is not linked to
the washer operation
• Combination switch
• Harness between rear wiper motor and BCM
• BCM
.
BCM
—
Rear wiper does not
return to the stop po-
sition. [Stops after a
five-second opera-
tion. (Fail-safe)]
• BCM
• Harness between rear wiper motor and BCM
• Rear wiper motor
Rear wiper stop position sig-
nal circuit
Refer to
Symptom
Probable malfunction location
Inspection item
NORMAL OPERATING CONDITION
WW-41
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
NORMAL OPERATING CONDITION
Description
INFOID:0000000012197066
FRONT WIPER MOTOR PROTECTION FUNCTION
• IPDM E/R may stop the front wiper to protect the front wiper motor if any obstruction (operation resistance)
such as a large amount of snow is detected during the front wiper operation.
• At that time turn OFF the front wiper and remove the foreign object. Then wait for approximately 20 seconds
or more and reactivate the front wiper. The wiper will operate normally.
REAR WIPER MOTOR PROTECTION FUNCTION
• BCM may stop rear wiper to protect the rear wiper motor when the rear wiper is stopped for 5 seconds or
more due to a snowfall.
• Rear wiper operates normally one minute after the obstacles are removed with rear wiper OFF.
WW-42
< SYMPTOM DIAGNOSIS >
FRONT WIPER DOES NOT OPERATE
FRONT WIPER DOES NOT OPERATE
Description
INFOID:0000000012197067
The front wiper does not operate under any operation conditions.
Diagnosis Procedure
INFOID:0000000012197068
1.
CHECK WIPER RELAY OPERATION
CONSULT ACTIVE TEST
1. Select “FRONT WIPER” of IPDM E/R active test item.
2. With operating the test item, check front wiper operation.
Is front wiper operation normally?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK FRONT WIPER MOTOR FUSE
Check front wiper motor fuse. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace the fuse after repairing the applicable circuit.
3.
CHECK FRONT WIPER MOTOR GROUND CIRCUIT
Check front wiper motor ground circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK FRONT WIPER REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1. Select “FR WIP REQ” of IPDM E/R data monitor item.
2. Switch the front wiper switch to HI and LO.
3. With operating the front wiper switch, check the status of “FR WIP REQ”.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> GO TO 5.
5.
CHECK COMBINATION SWITCH
Perform the inspection of the combination switch. Refer to
Is combination switch normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Repair or replace the applicable parts.
Lo
: Front wiper LO operation
Hi
: Front wiper HI operation
Off
: Stop the front wiper.
Monitor item
Condition
Monitor status
FR WIP REQ
Front wiper switch HI
On
Hi
Off
Stop
Front wiper switch LO
On
Low
Off
Stop
WASHER TANK
WW-43
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
REMOVAL AND INSTALLATION
WASHER TANK
Exploded View
INFOID:0000000012197069
Removal and Installation
INFOID:0000000012197070
REMOVAL
1. Fully open hood.
2. Remove washer tank inlet fixing clip (A).
3. Pull out washer tank inlet (1) from washer tank.
4. Remove fender protector RH (front). Refer to
EXT-31, "Removal and Installation"
5. Disconnect washer pump connector.
6. Disconnect washer level switch connector (Canada models only).
7. Disconnect front washer tube and rear washer tube.
8. Remove washer tank mounting bolts.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
1.
Washer tank inlet cap
2.
Washer tank inlet
3.
Front washer tube
4.
Washer pump
5.
Rear washer tube
6.
Packing
7.
Washer tank
8.
Washer tank (Canada models only)
9.
Washer level sensor (Canada mod-
els only)
A
: Clip
: Vehicle front
: N·m (kg·m, in-lb)
JMLIA1731GB
: Vehicle front
JMLIA1158ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст