Nissan Juke F15. Instruction — part 724
EXL-116
< REMOVAL AND INSTALLATION >
[XENON TYPE]
REAR REFLEX REFLECTOR
REAR REFLEX REFLECTOR
Exploded View
INFOID:0000000012201709
EXCEPT FOR NISMO AND NISMO RS
NISMO AND NISMO RS
Removal and Installation
INFOID:0000000012201710
REMOVAL
Except for NISMO and NISMO RS
1. Remove rear bumper fascia lower. Refer to
EXT-23, "Removal and Installation"
1.
Rear bumper fascia lower
2.
Rear reflex reflector LH
3.
Rear reflex reflector RH
: Pawl
: N·m (kg-m, in-lb)
JMLIA5406GB
1.
Rear bumper fascia lower
2.
Rear reflex reflector RH
3.
Rear reflex reflector LH
: Metal clip
: Vehicle front
JMLIA3679ZZ
REAR REFLEX REFLECTOR
EXL-117
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
2. Remove rear reflex reflector fixing screw.
3. Disengage rear reflex reflector fixing pawls, and then remove rear reflex reflector.
NISMO and NISMO RS
1. Remove rear bumper fascia lower. Refer to
EXT-23, "Removal and Installation"
2. Disengage rear reflex reflector fixing metal clip, and then
remove rear reflex reflector according to numerical order 1
→3
indicated by arrows as shown in the figure.
INSTALLATION
Install in the reverse order of removal.
JMLIA3680ZZ
EXL-118
< SERVICE DATA AND SPECIFICATIONS (SDS)
[XENON TYPE]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Bulb Specifications
INFOID:0000000012201711
EXCEPT FOR NISMO AND NISMO RS
NISMO AND NISMO RS
Item
Type
Wattage (W)
Headlamp
High Beam
HB3 (Halogen)
60
Low Beam
D2S (Xenon)
35
Front combination lamp
Front turn signal lamp
WY21W (Amber)
21
Front side marker lamp
W5W
5
Parking lamp
LED
—
Front fog lamp
H11
55
Side turn signal lamp
LED
—
Rear combination lamp
Tail lamp (LED)
LED
—
Stop lamp/Tail lamp
(Rear side marker)
W21/5W
21/5
Rear turn signal lamp
WY21W (Amber)
21
Back-up lamp
W16W
16
High-mounted stop lamp
LED
—
License plate lamp
W5W
5
Item
Type
Wattage (W)
Headlamp
High Beam
HB3 (Halogen)
60
Low Beam
D2S (Xenon)
35
Front combination lamp
Front turn signal lamp
WY21W (Amber)
21
Front side marker lamp
W5W
5
Parking lamp
LED
—
Daytime running light
LED
—
Side turn signal lamp
LED
—
Rear combination lamp
Tail lamp (LED)
LED
—
Stop lamp/Tail lamp
(Rear side marker)
W21/5W
21/5
Rear turn signal lamp
WY21W (Amber)
21
Back-up lamp
W16W
16
High-mounted stop lamp
LED
—
License plate lamp
W5W
5
PRECAUTIONS
EXL-119
< PRECAUTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000012201712
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Instruction.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, it is recommended that all maintenance
and repair be performed by an authorized NISSAN/INFINITI dealer.
• Improper repair, including incorrect removal and installation of the SRS, can lead to personal injury
caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module,
see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery or batteries, and wait at least 3 minutes before performing any service.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000012965028
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
Precautions for Removing Battery Terminal
INFOID:0000000012965039
When disconnecting the battery terminal, pay attention to the following.
• Always use a 12V battery as power source.
• Never disconnect battery terminal while engine is running.
PIIB3706J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст